Question about Office Equipment & Supplies

1 Answer

I was given a laminator but it does not have instruction booklet, how does it work?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 313 Answers

The main way they work is that you have the laminate pouch into which you slide your paper then make sure that the pouch is put between the guides closed side first the machine will take a while to warm up after you have plugged it in when the green light is on push the pouch in slowly the motor should turn and feed the pouch in automatically.. the important thing is to make sutre the pouch is correct for the type of machine you have and that when feeeding in the pouch it goes in closed end first otherwise it could open and jam.. Good luck A>>

Posted on Jul 31, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does anyone know how to get an item unstuck?


open their cover at the back of the machine.try to pull it from an anticlockwise direction..

390fc732-bfe8-4aeb-a496-7c7b77eb08a3.jpg

May 29, 2015 | Office Equipment & Supplies

1 Answer

Laminate did not come out it just went back inside on roller


warm the machine back up, get the glue sticky again, then work it off, either by going in forward or reverse, whichever works best for the given situation. Don't use anything sharp as the rollers damage easily....very expensive

Sep 09, 2014 | Gbc Heat Seal Ultima 65 Laminator 1710740

1 Answer

Guess I'm not too bright. Have a pack of GBC SelfsSeal Laminating Sheets, 9 x 12. Instructions say "Center item face sown on the clear non-adhesive." "Peel away the liner and...


It's not you, it's the instructions. They are just wrong and will not work as directed. However, I have found a way to use these sheets that works for me, but it is still not particulary easy.

Step 1) Lay the 1st sheet on a flat surface, adhesive side up. Pressing down on the small 1/2" strip of backing, peel away the large backing sheet exposing the adhesive. Holding the sheet you want to laminate face down and at an angle to the work surface, carefully align the material by "bumping" it up against the edge of the 1/2 strip. Once aligned, carefully and gradually lay the item onto the adhesive. Like I said, not particularly easy, but if you are careful, it will work.

Step 2) If you want to double laminate, which I usually do, the second laminate sheet seems easier to me. Leave the Step 1 laying flat on the work surface. Take a second lamination sheet and again, hold it down on a flat surface and peel away the large backing sheet, leaving the small 1/2" backing attached. Take this 2nd sheet and holding it over the 1st, face down and angled up from the work surface, align the 1/2" strips of both sheets together and again carefully lay the 2nd sheet over the first single-laminated item. The two 1/2" strips don't stick to one another allowing a bit more flexibility for alignment.

Press all of this together and work out any bubbles or wrinkles. Once that is done, pry the two sheets apart at the very edge to remove the two 1/2 strips.

Unless you are incredibly lucky the edges will never align 100%. I use a paper-cutter to trim off any irregularities after I finish laminating.

Apr 11, 2011 | Gbc Selfseal Letter-size Laminating Sheets...

2 Answers

User manual


Hope this link helps:
http://www.retrevo.com/support/Uniden-DECT2060-Telephones-manual/id/3141bh548/t/2/

Jun 10, 2010 | Uniden Cordless Phone

1 Answer

Where can I obtain a Cannon 10588G instruction booklet


Go to Cannon website. Have model # and serial#, and look it up.

Apr 06, 2010 | Cannon 10476G Dual Fuel (Electric and Gas)...

1 Answer

I was given an older camera and need instructions to operate it.


You didn't specify the camera model, but you might find the appropriate manual at htttp://www.butkus.org/chinon/vivitar.htm

Apr 05, 2009 | Vivitar Photography

1 Answer

REQUIRE INSTUCTION BOOKLET


http://esupport.sony.com/CA/perl/model-documents.pl?mdl=DSCP43&LOC=3

Dec 02, 2008 | Cameras

1 Answer

Instruction booklet


Hi - You can download the manual by clicking the link underlined in blue below:

GR-SXM260U

33952e4.jpg

Other info here.

Please take a moment to rate this solution & let us know if the information given was useful to you - Good Luck!

Informatica

Sep 03, 2008 | JVC GR-SXM260U Camcorder

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

k24674

Level 3 Expert

7993 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...