I had someone come to my town, and I noticed my house was gone, and it was behing my museum where i couldnt get in it... i turned it off without sawing and i turned it on and i cant get past the screen where it says its been loaded
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
The first condition of understanding a foreign country is to smell it!. A city trip to Frankfurt will surely be exciting if you are planning for one. I feel so happy to share my trip experiences in Frankfurt. The places that I had been to here are the Romer, Maintower, Stadel, Senckenberg Museum, Goethe House and Museum and the Art City called The Frankfurt Museum of Modern Art. All these places were really worth spending time with and I thoroughly enjoyed my trip and thanks to the tour coordinators, Bus Charter Frankfurt for arranging a well planned and good trip to Frankfurt.
We designed and built a house in TN in 2000 and special ordered brick for it. We looked through some samples and chose brick that appeared to have subtle fossil and leaf patterns. The brick was delivered to the house site.
If the power brick is plugged into a surge protector then try to plug it directly into the wall outlet instead (note: xbox power brick has it's own surge protector)
Make sure that the brick is clean and the ventilation holes are not blocked.
Unplug ALL cables from Xbox 360 and plug back in securely. (note that though some cables might appear to be secure but they might not be seeded correctly. Verify.)
Check power source and make sure there is no fluctuating current preventing stable current to the Xbox 360 when attached? Try to plug the xbox into a set in another room and see if it corrects itself. If so then you know that possability of outlet issue is likely.
i have found all my firm where i have seeded Raseberries and others are not accessable ,neither i do ploughing or delete nor i hervest it shows green land but not accessable... need help to play more otherwise soon i have to quit such a good game..
I'll give you the rundown. First, for a driveway, I'd have to advise using a pretty thick slab of concrete beneath the brick. The concrete part of it should be done professionally. But I live in an area with lots of rain (hence, Mud), might not be a problem where you are. Anyway, here you go:
Clear the area so its smooth. Grade it if necessary.
After clearing the area, set the perimeters with string or with 1x4 boards. This keeps you from going wide as you lay the bricks
Get a load of sand and spread it evenly over the area. This can be done easier with two people and a long 2x4. The depth should be at least an inch. This makes leveling the bricks MUCH easier. Keep some aside for filling in the spaces between the bricks. Keep it dry too.
Start at one end and start placing the bricks. As you advance, you'll be on the bricks, not the sand.
Have a straight edged board handy to level them. Use a rubber mallet to tap them down. Consider the spacing between them. Use a scrap of 3/8 wood or something like that to keep the spacing consistent.
As you place more bricks, get up occasionally and eyeball your work.
After they are laid, you'll need to hit a home improvement place. You are looking for a glue (powdered) that is mixed with your left over sand to set the bricks. Ask someone there, they will know.
You mix it in with the sand and dump it in the middle of the bricks. Then just sweep it over the entire area until the spaces are filled. Then sweep off the excess.
Once filled, lightly spray water over the whole drive. This activates the compound. Once dry, you have a driveway.
If you do concrete it first, you'll only need enough sand for the space fill.
First thing to try is to remove the power brick (not just the cord the whole brick) from printer for a minute then re insert and try it again. If this doesn't help try uninstalling it then re installing the printer