Question about Whirlpool Duet GHW9150P Front Load Washer

1 Answer

My Control Lock is on and I cant get it to go off?????

I try unplugging it and everything else nothing works

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,294 Answers
Re: My Control Lock is on and I cant get it to go...

Press "end of cycle" button for over 5 seconds, the child lock comes off. All the best, and dont forget to RATE me.....

Press it again and the child lock comes on, simple eh?

Posted on Nov 25, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

LOC showing on screen

Hello Annie, thank you for allowing me to assist you!

I see you are still receiving error code "LOC" even after replacing the door lock assembly. Let's try unplugging your washer once again to determine if it is a false error code. It is important to wait roughly ten minutes and then turn your washer on. Before selecting a cycle, press OPTIONS and SELECT at the same time for 20 seconds until "LOC" is no longer displayed. If the error code does not clear, then your washer more than likely may be experiencing an issue with the control board or wiring harness. I hope this information helps to some degree.

Feb 18, 2014 | Electrolux EW1000i Front Load Washer

1 Answer

Control lock on duet washer GHW9250ML1 is flashing, nothing working even after unplugging. When replugged, light starts to flash again and nothing else.

Here's what the Duet tech sheet says to do:

1. Press PAUSE/CANCEL button on the touch-pad twice.
2. Drain the unit, then check that the Drain hose and Drain Pump
Filter is clear of foreign objects.
3. Check/ Replace Touch-pad/LED assembly.
4. Check harness connections.
5. Check the CCU.

Oct 25, 2011 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

I have a Oasis, model 110 270 826 02, serial #CT3270410, that I just had the touch pad ERC control part (8564392) replaced last week. Today when I went to use it, the DU comes up on the control panel...

The DU error code indicates that the control detects a problem with the washer door (lid) unlocking. In this situation, the failure is normally caused by a failed door lock assembly. I provided technical information on this failure in the first image below. You can use this information if necessary to verify a failed lid lock assembly. The control is apparently sending the voltage to the lid lock mechanism to unlock the door but is not sensing that the lid is unlocked. There is a chance that you have a wiring failure or a bad control board so it is best to thoroughly diagnose the failure if possible before replacing components. Be sure that you unplug the washer before accessing internal components. If you determine that you have a failed lid lock assembly, you can use the procedure shown in the second image below to replace this component.
richroth_44.jpg richroth_45.jpg

Jan 10, 2011 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

Control lock llight is on kenmore duet washer

hold the end of cycle button for three seconds it should come unlocked then

Apr 25, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

My duet washer says control lock and i cant get it to do anything i tried to unplug it to reset it but not working still has "control lock " lit

The following link explains how to correct a Control Lock problem on a Whirpool Duet:

If these procedures do not correct the problem, you may have a more serious problem. If you need further assistance, please let me know. I hope this helps you.

Jul 26, 2009 | Washing Machines

1 Answer

The washer is stuck on control lock

happy new year help has arrived...always unp[lug this time i cant tell you why it locked up,,but i can take you through opening manually,,ok just step by step...unplug lookdown at that bottom toe panel,,,remove 1/4 nut diver,,,slow now your going to reach up right under the door switch on the bottom of that assembly is atear drop tab just pull it,,,,,now the door is opened,,,

Dec 30, 2008 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Control locked

I ended up unscrewing the top from the back, my husband pushed the drum slightly forward and I reached my hand down the side where the door locks and there is a plastic "thing" (almost like a tab) that you pull down and you can hear it click and my husband easily opened the door

Sep 14, 2008 | Washing Machines

1 Answer

Control locked

look on consoles for small lock emblem hold that button down 3-5 secs

Sep 01, 2008 | Whirlpool GHW9200L Front Load Washer

3 Answers

Control lock light on-door opens-won't start

Press 'control' + 'pause:lock' +
'temperature' for 5 seconds
'end of cycle' for 5 seconds. Tell me which worked & rate me pl.

Apr 16, 2008 | Whirlpool GHW9150 Front Load Washer

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

Related Topics:

256 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides