Question about Bamix Blenders

1 Answer

Bamix De Luxe Hand Mixer - cutter guard

The cutter guard has come off my Bamix De Luxe Hand Mixer . It looks like it should just screw back on as it seems to have a thread but I can't seem to get the 2 threads to 'catch' each other to allow me to screw them together . Is there a special way this has to be done ?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer
Re: Bamix De Luxe Hand Mixer - cutter guard

Instructions state to remove it, turn it clockwise, so the opposite remains true. To replace it, turn it counterclockwise.

Posted on Sep 11, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

What is the thread size on the knife cutters of the Kitchenaid KSB555.

The thread that the driving clutch screws onto measures 6.2mm with my calipers measuring the thread. Confirming it is left hand thread.

Aug 25, 2015 | KitchenAid Blenders

1 Answer

How can I Loosen the spring blades on a Bamix mixer attachment

You are lucky. they usually fall off mine.
However you can gently ease them off with small needle nosed pliers.

May 23, 2014 | Bamix Blenders

1 Answer

The plug has sheared off,can I have it replaced by an electrician or do I have to return it to Bamix.

Remove the 2 screws on the top cover with a security torax screwdriver.
The cord and switch assembly will lift out quite easily.

Solder on the new cord.
Put the cover back on.

Jun 11, 2011 | Bamix Deluxe Handheld Blender

1 Answer

I have a bamix M200 hand blender & the shaft does not turn although the motor is working can you help?

After a period of time food residue will migrate up through the seal on the "foot" and lodge in the shaft. Once this is gummer up the motor will go but the shaft will not be able to rotate.

The machine will need to be disassembled and the shaft cleaned out. I recommend that you find your local Bamix Service Centre to do this as there are fragile parts in the stick mixer.

May 21, 2010 | Bamix Deluxe Handheld Blender

2 Answers

Shaft does not turn still vibrates

Same happened on mine. It is a M100. I pulled off the blade and guard (screws off the opposite way to normal), lifted the black rubber seal on the shaft as far out of the way as I could and cleaned it out. I then put a little WD-40 down the shaft and waited a while and twisted the shaft a little with pliers to work in the WD-40. After a few minutes it ran and fairly quickly came up to full speed.

Nov 08, 2009 | Bamix Deluxe Handheld Blender

1 Answer

The motor on the Bamix hand mixer is working properly yet the spindle will not spin. It appears as if it is not engaging. The spindle is not jammed.

there is a rubber connetion between the motor spline and the spindle which holds the screw that connects to the spindle, this has broken

Jun 09, 2009 | Bamix Immersion Handheld Blender

1 Answer

Bamix stick blender Handle vibrates but shaft does not turn

Old food residue and juices will have got into the shaft bearings, and have dried out enough in 9 years to stop it turning. Starting with the simplest solution, try immersing the shaft in hot, or even boiling, water nearly up to the top of the metal shaft. CAUTION - DON'T BURN YOURSELF! Let it stand in the water for a few hours, and then try turning the shaft by hand (with the machine unplugged, of course). This could be repeated a number of times. You may also be able to unscrew the blade guard after this treatment, bear in mind it has a left hand thread, so if you are looking at it from the bottom, turn it clockwise to loosen. Be careful not to lose any seals or springs when it comes off.

If this doesn't work, support the Bamix upside down, and pour a small amount of WD-40 into the blade guard, so that it pools around the end of the shaft. Leave to stand, and the oil should slowly seep into the bearings, dissolving the food residues. Again, try this a few times.

If neither of these work, the Bamix will need to be dismantled to clean the shaft and bearings. This is really beyond the scope of this forum and requires some experience of this type of work.

Mar 13, 2009 | Blenders

1 Answer

Bamix hand blender 2 speed

I found this rubber drive coupling on mendshed which were helpfull enough to place it on their ebay site for shipping outside of the US. Check if it looks like yours first. One end the tapered end screws into the drive shaft the other end just fits in the rectangular shaft of the motor.

Sep 08, 2008 | Bamix Blenders

1 Answer

My hand mixer stopped working.

Have you tried greasing it near the blade. I read in my instruction book that sometimes they seize if they aren't used often. They also suggest trying to soak the wand in a pot of hot water for a minute or two and then trying to use it in the water. Hope this helps

Aug 30, 2007 | Bamix Gastro 200 Handheld Blender

Not finding what you are looking for?
Blenders Logo

Related Topics:

366 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bamix Blenders Experts

Ruth summersides

Level 2 Expert

482 Answers

L Pfaff
L Pfaff

Level 3 Expert

11572 Answers

Stan Ford

Level 3 Expert

2170 Answers

Are you a Bamix Blender Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides