Question about Zenith D52WLCD 52" Rear Projection HDTV-Ready Television

1 Answer

T.v. just went out i have a zenith 52" is thier a reset button or something?

Tv. was on, and all of a sudden it just went out. We tried turning it on and off but it just wont come on. I think its a 89 or 90 model and we never had it serviced because we had never had any problems with it. Please help me my guess are comming from out of town and we need tv to entertain.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.


    An expert who has answered 200 questions.

  • Expert
  • 208 Answers

Most likely the lamp failed, check your owners manual for instruction on the lamp replacement.

Posted on Feb 10, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

My 52 ince screen stopped showing picture. It is just red, or yellow or green with thin vertical lines. I can hear that the channels are changing but no picture. Is there a reset button or something?

To reset the tv to factory/ default settings, please follow below procedure.
Turn On the TV, while holding down Up Arrow on the remote control, press Power button on TV, tv will turn itself Off then back On again, release Up Arrow on remote control.
This procedure will reset all settings in tv to default settings.
Problem seems with lcd panel and I'm afraid it does not seems to get solved by resetting tv however try to reset tv by above said procedure.

Aug 04, 2011 | Sony BRAVIA KDL-52W3000 52 in. LCD...

1 Answer

Tv wont turn on... light blinks yellow as if its going to power on.. and just shuts off... for my zenith dlp 52 inch tv

I had this same problem. The Zenith rep told me to unplug the TV, hold the power button down for 30 seconds, plug it back in and then turn it on. It worked and I haven't had a problem with it since. I hope this helps. Good Luck!

Mar 06, 2010 | Zenith D52WLCD 52" Rear Projection...

1 Answer

52" dlp


Jun 16, 2009 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

52 inch zenith shuts down after 10-30 seconds

Bulb must be replaced before viewing will continue.

May 17, 2009 | Zenith D52WLCD 52" Rear Projection...

1 Answer

52" plasma tv - turns on - and I hear something reset inside

i hear a clicking noise- the clicking noise is most likely you ballast trying to power the lamp, but failing. this may indicate a defective ballast if you have recenty purchased a new lamp.I recomend you have your lamp tested to help narrow down the cause of the defect. It's highly unlikely for a new lamp to be dead on arrival

Dec 04, 2008 | Dell Televison & Video

1 Answer

How to reset lamp hours

try holding the enter button on the tv and the mute button on the remote. a reset screen will pop up and then just press the center direction button twice.

Sep 04, 2008 | Zenith D52WLCD 52" Rear Projection...

1 Answer

Tv will not turn on after sudden power outage

you most likely blew a fuse the only "reset" is to unplug the t.v. and leave it unplugged for a few mins, then make sure that you hold down the power button to drain the power out of the t.v.then turn it back on.... only other reset sequence is for removing the parental code

Jun 24, 2008 | Zenith C27A24T 27" TV

1 Answer


I just found the solution on another model of Zenith TV. Hold the enter button down on the TV and the MUTE button on the remote. In approx. 5-7 seconds a screen will pop up asking if you want to reset the lamp timer. Hit the bullseye button in the middle of the arrows and it will reset. Worked perfectly.

Apr 15, 2008 | Zenith D52WLCD 52" Rear Projection...

1 Answer

"my tv just went out"

Most likely your lamp has failed and your owners manual will show how to replace the lamp.

Nov 21, 2007 | Zenith D52WLCD 52" Rear Projection...

Not finding what you are looking for?
Zenith D52WLCD 52" Rear Projection HDTV-Ready Television Logo

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zenith Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75017 Answers

matt martin
matt martin

Level 3 Expert

1213 Answers

Computer Repairing
Computer Repairing

Level 3 Expert

14641 Answers

Are you a Zenith Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides