Question about Zanussi 24 in. DE6965 Built-in Dishwasher

1 Answer

AL3 I have AL3 flashing up on my machine and i don't no what it means' can anyone help?

Posted by on

1 Answer

Re: AL3

Possibly tge heating element,I am having the same problem .When I check during the operation it appears that the water is not heating up. Only runs the rinse programme without the error message as I assume that uses cold water only?

Posted on Mar 21, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

NEMO- Fast light flashing not turning off. Machine is off with door open. Why is this?

Washing Machine Fault Diagnosis - How to repair > Home > Washing machines
Nov 11, 2014 - Washing machines drum not washing, turning or spinning. ... This is most likely a new electronically controlled machine and the flashing lights ... I pulled the top of the machine off to look see if there was a visual fault but can't see anything out of place. ... It allowed me to open the door and take the wash out.Missing: nemo

Washing machine lights flashing - White Goods Help > ... > DIY Washing Machine Repair Help
Jul 9, 2013 - What it means when washing machine lights flashing. ... If your washingmachine stops working and you can see some of the lights flashing, or one or ... For example, the door locked indicator may flash 7 times, pause, and flash ... put the bolts that go where the motor is back on as the belt kept slipping off.Missing: nemo

My Nemo F&P dishwasher just stays in the wash cycle on and > Australia Whitegoods

Jan 12, 2016 | Fisher and Paykel Dishwashers

1 Answer

Dishwasher not doing anything

hi does anyone know what error A06 for the Hotpoint Aquarius FDW70 means and if it can easily be fixed

Jun 13, 2013 | Dishwashers

2 Answers

The Zanussi Aquapulse (de 6965) Fault Code AL3.

i have this now- another site suggested its the heater, or rater the circuit board. I have just taken it apart and have two dry solder points that are identified quire easily by soot around the area. so now off to find my soldering iron!!

Sep 26, 2009 | Zanussi 24 in. DE6965 Built-in Dishwasher

1 Answer

E4 fault code

Hi, when a dishwasher goes into overfill mode it usually means that the bottom tray has water in it that operates a float connected to a microswitch. Open the bottom panel and soak up all water then check to make sure the float is down completely.then restart dishwasher. Why it has overfilled is another problem. It could be a faulty pressure switch,pressure switch hose may have a hole in it, water valve may be faulty. Too much soap or wrong soap can cause too many suds and hence overfill.Also if rinse aid is spilt when filling. Or seals leaking. etc.

Feb 02, 2009 | Dishwashers

1 Answer

Dishwasher prog light is flashing and pump is running nothing els

ok, just a few minutes after posting this as a fault, I have opened the covers, the machine has a leak, the undertray has a sensor which has detected this, flashing light (prog 45 degC wash) flashing is a code to indicate leak sensor active.
Other prog lights flashing indicate a different fault, the following details each... this is a cut/paste from another forum site, copied without permission....

jawa592rc_a04.gif on 6th Feb 2008
Cannot guarantee 100%accurate but you all might like what the flashing fault codes actually refer to, note what follows are pointers to what bit has gone wrong only. You should have the programmes running left to right: led1=intensive,led2=normal,led3=eco,led4=fast,led5=prewash,led6=delicate wash.ok so when this heap of western european tosh goes wrong one or two lights will flash this is what they mean:led3=m/ch has o/flowed water . ie the base underneath has sensed a leak.4=i/let h2o valve u/s or slow fill.5=thermister(electronic thermostat) is u/s or more likely the pcb .6=timeout heating which means the thermister senser between the door halves has become faulty or detached.3+4=no pump out,slow pump out,pcb u/s,blockage.4+5=tap off i/let valve.3+5=wash motor not coming on -seized,winding o/cic.but can also mean mesh plte filter badly blocked.1+4software fault with pcb.4+6=heating cic u/s (usually the heater tube )but can be the heater relay on pcb.3+4=pcb u/s.I don`t except any responsiblity for this being spot on or near spot on!! hope this helps someone.Try NOT to electrocute yourselves please!! If your not at all confident walk away and get "someone" who knows what they are doing.Cheers. jawa592

Jan 21, 2009 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

First flashing light.

I've just had this issue and managed to get it working again.

The problem is more than likely water sat in the bottom of the machine. Unload and unplug your machine. Tip it backwards by about 45 degrees, and you should notice about 1/2 pint of water leaking out of the back on to the floor (make sure you have some old towels handy).

After doing this my machine started to work again.

Nov 02, 2008 | Indesit 18 in. D41 Slim-Line Free-standing...

1 Answer

Indesit dishwasher DI 450 wont work

I had this problem and you have probably resolved it by now but I thought i would respond so that anyone else searching would get some help!!!

If program 2 and 4 are flashing it means that the filter is clogged and needs to be cleaned. Switch the dishwasher off - take out the filter and clean it and ensure all debris removed from in the filter housing. Pop it back in and switch back on and now the machine should work.

Mine is now running good as new!!

Aug 18, 2008 | Samsung 24 in. DB5710DT Stainless Steel...

1 Answer

Electrolux Gallery Dishwasher Error Message AL3

It sounds like it could be a heater problem, I would check this first

Nov 26, 2007 | Dishwashers

3 Answers

Start light flashing

start light on and no other action could mean that the door catch has gone faulty, test accordingly and replace if needed, no wash cycle will work if this item is faulty, the waste outlet pump may be the only part that will work on some models, this is a safety feature hope i have helped if so please rate me, work safe unplug when testing

Sep 21, 2007 | Whirlpool GU2400XTP Built-in Dishwasher

4 Answers

Hotpoint Aquarius+ FDW70 Error Codes

i have the same on my dishwasher and have just been looking on the net. Found out that the error code A10 means open/short circuit fill value traic. Whatever that means!!! and to book a service engineer. Hope that helps

May 04, 2007 | Hotpoint 24 in. FDW60 Free-standing...

Not finding what you are looking for?
Zanussi 24 in. DE6965 Built-in Dishwasher Logo

Related Topics:

479 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers


Level 3 Expert

1772 Answers

Are you a Zanussi Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides