Question about Intex Pool & Spa

Open Question

Intex spa temp controls frozen - Intex Pool & Spa

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 32 Answers

SOURCE: The water froze in my intex spa and control beeps. Cant turn temp up. What do I do?

Try using a blow dryer to unfreeze the water.

Posted on Jan 11, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pure spa control panel film or diagram where is fuse


open up control panel schematic inside cover

Jan 17, 2016 | Intex Pool & Spa

1 Answer

Intex purespa displays current water temp but will not turn on or start filter/bubbles. Bought 1 mo ago: just set it up a week ago. Was working fine for 1 week. TrI'd unplug and reset. Any ideas??


is displayed temp less than 2 degrees than setpoint temperature ? its possible this situation will disallow the pump to go to high speed and the air infusers to work till spa heats back up , or can be a heater fault as well

Aug 15, 2015 | Intex Pool & Spa

2 Answers

My spa temperature light is blinking. It is set at 104 and the temperature is showing 118. Why is the temp blinking?


If you can contact your spa manufacturer they will usually send you the manual for your unit at no cost.
If the temperature is set at 104 it is at the high end of the safe temperature for a human. 102 is recommended, and 103 is OK for 15 to 20 minutes maximum.
If your spa is actually at 118 degrees, it could easily cause very severe medical heat distress. I would strongly recommend NOT using it until you can get the temperature down.
It's possible that the blinking light is a warning.

Jun 14, 2015 | Intex Pool & Spa

1 Answer

When the pump is plugged in the heater an jets run the jets won't turn off


Sounds like bad controller?

Do you still have problem?
Use Comment link on this thread, and inform this forum what you may gave done this far?
Did you fix it? Did Intex help? What was problem?
If not...

Support Intex

Dec 22, 2014 | Intex Pool & Spa

1 Answer

My intex spa shows error 96 and 143 degrees F. water is cold


well first the manual should say what a error 96 is but i'll save you the trouble , the control is saying heater failure as the water should never be 143 degrees this would burn/kill you if you got in , id look at temperature probe 1st (its in pipe right past the heater ) and next id look at control itself , sometimes water intrusion dammage in controller makes for some "funny" and wrong things to happen

Oct 12, 2014 | Intex Pool & Spa

1 Answer

Why won't my intex spa heat?


is the recirculation pump running if so check filters or it could be tmp sensor

Aug 04, 2014 | Intex Pool & Spa

1 Answer

My spa won't turn on an just beeps.


sounds like temp sensor is either loose or bad if only two weeks old call who you bought it from should be warrantied

Jul 27, 2014 | Intex Pool & Spa

Not finding what you are looking for?
Pool & Spa Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Intex Pool & Spa Experts

Jay Finke
Jay Finke

Level 3 Expert

1338 Answers

Mike

Level 3 Expert

4336 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Intex Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...