Question about Pioneer Televison & Video

1 Answer

Pioneer Media Receiver PDP-R06U "input 1" is totally inop. Switching HDI's to other input proves it is defective. Can it be reset? Otherwise the 2nd input is not available for DVD/BluRay, etc

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pioneer Master
  • 9,324 Answers

Pioneer PRO R06U Training Manual This manual is more than just an operator's manual. What it takes to repair it will be found in it.

Posted on May 12, 2017

Testimonial: "I am sure the training manual is helpful in many instances but in this case, I see NOTHING that aids in correcting the matter with "input 1" being inoperative."

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pioneer media receiver pdp r06u


no if it didn't have a tuner it would not even have a picture he is lying

Jan 28, 2014 | Pioneer Plasma Media Receiver Pdp-r03u

3 Answers

PIONEER PDP-R06U / PRO-R06U MEDIA RECEIVER SERVICE


Hey,
This may be too late...
I got it from the field manual.

Trap Switch Reset Procedure
G-4, G-5, G-6, G-7, G-8
• Replace media receiver, plasma panel cover, or tape down HDCP trap switch.
If the model in question has the TV Guide option, the TV Guide
option must be turned off before proceeding.
• Using the customer’s remote control enter “service mode” by pressing the
following key sequence:
1. Press the “display” button then release the “display” button.
2. Wait between 3 and 7 seconds
3. Press and release the “<”, “^”, “<”, “>”, and “power” buttons in sequence.
• Panel will now turn on in “service mode”.
4. Press “muting” button 3, 4 or 5 times depending on model you are working on.
Until the display shows the “initialize” page.
5. Press and hold the “display” button until the error indicator (red LED) on
either the panel or the media receiver goes out.
6. Exit service mode by pressing the “power” button on the remote.

I had to try it a couple of times before I got it to work. I.m not too sure how to turn off the tv guide mode. I just held it in for a couple of sec,s.

Good luck

Dec 05, 2009 | Pioneer Audio Players & Recorders

1 Answer

Pioneer PDP-RX06XE has no picture


check PDP 436XPE UNIT may be Y board short...or need factory restore to the original state....

Nov 18, 2009 | Pioneer PDP-4350HD 43 in. Plasma...

1 Answer

I have a Pioneer pdp-433 plasma with a media receiver pdp-ro3e. When switching it on it gave a loud pop and blew up a fuse in the meter cupboard. Now when switching it on it gives green light on receiver...


Alas, the powerblock has gone.

Common problem on this model.

Only solution is replacement powerblock.

Pioneer used to repair this for nothing even out of warranty (they did for me), but they may not be so willing now, as your tele must be at least 6 years old. Unfortunately, it will be cheaper to buy a new TV than to pay for a contractor to fix it.

Brian

Jul 13, 2009 | Pioneer PureVision PDP-4330HD 43 in....

1 Answer

Pioneer PDP-R06U media receiver


On this model, this is a "fault code". The unit has attempted to power up and the processor has determined a fault with it's "self check" diagnostic test it runs each time the unit is turned on. A technician will have to test the unit to determine the nature of the fault.

Feb 27, 2009 | Televison & Video

1 Answer

Upgrading media receiver on Pioneer PlasmaPDP-5030HD


You can use a PDPR06U if you can find one for sale its 2 generations later than your's. Look on Ebay. I might have one too but I got to look.


Jan 04, 2009 | Pioneer PureVision PDP-5040HD 50 in....

1 Answer

PDP-436PG


maybe its not worth the effort. the media or turner box must corsponed with the model of the pioneer tv, in order to work.

Apr 09, 2008 | Pioneer PDP-4360HD 43 in. Plasma...

1 Answer

Can I use media receiver PDP-R04U with PDP-436PU display?


You need the pioneer media cables hooked up to the media receiver to the plasma unit itself. each end has 2 different plugs. one has 2 thumb screws and the other is a squeezable end that clicks into place. They MUST be on before you plug in any power what so ever!!!! And yes, other information is being passed through.

C-Dog

Sep 18, 2007 | Pioneer PureVision PDP-4340HD 43 in....

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Televison & Video Experts

The Knight
The Knight

Level 3 Expert

73691 Answers

Jaime Hernandez

Level 3 Expert

2315 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Are you a Pioneer Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...