Question about CircuPool Pool & Spa

Open Question

I HAVE 3 FILTERING SYS RUNNING OUR POOL. (1 NEW VARI PUMP, 1 FIL, 1 CARETAKER). CAN'T AFFORD 3 CIRCUPOOL. CAN I PUT 1 CIRCUPOOL BY ITSELF TO 1ST FIL SYS, AND 2ND CIRCUPOOL TO THE 2 REMAINING FIL SYS?

Can 2 pumps, 2 filters, and 2 cleaning systems be connected to 1 RJ PLUS SERIES ELECTRONIC CHLORINE GENERATOR? DO I NEED SPECIAL WIRING OR IS CIRCUPOOL MADE FOR TWO SYSTEM CONNECTIONS? SHOULD I SEPARATED SYSTEMS THANK YOU, NOEMI ELIZONDO, ALICE TX 361-562-3186

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 119 Answers

SOURCE: I have a Whisperflow pool pump attached to a

somewhere air is getting into the system look for a crack or hose that might be doing this.

Posted on Apr 19, 2010

  • 22 Answers

SOURCE: I have a Whisperflow pool pump attached to a

there may be some debris at the pump lid oring that is allowing some air to get sucked in. sometimes everything seems to be operating fine until the system gets up to full pressure. perhaps the pump has run dry at some point and the pipe that threads into the front of the whisperflo pump has broken the seal. make sure the pipe is dry and then turn on system. you can use duck tape or squeeze silicon sealer into threaded area this will usually at least allow you to notice that less air is entering the system that way you dont have to cut and replumb parts you don need to. you may want to check any valves that are in the pipes that lead to the front of the pump it is possible that the flap at the skimmer throght where the water comes in at the pool wall tile/water line is sticking up and or is getting stuck which will stop the amount of water needed to enter thru the skimmer basket area once the pump is in full prime this then lets the water drop inside skimmer basket area and air gets sucked into the pump then the process repeats over and over until the flapper is freed or removed

Posted on May 14, 2010

Geekman
  • 32281 Answers

SOURCE: I have a Intex Krystal

The most like problem is the chlorinator has stopped working.
Most salt water chlorinators have a circuit breaker which cut power to the electrolyte cell if there is an overload or short condition. Check the circuit breaker, reset is necessory.
The other possible problem with the chlorinator is that voltage/DC current is supplied to the electrolyte cell via a low voltage transformer and rectifying circuit. if these components are faulty then the electrolyte cell will not produce chlorine. When the electrolyte cell is working normally you can see tiny bubbles of hydrogen and oxygen coming off the cell.

Posted on Sep 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I backwash my sanddollar pool filter


Shut the pump off, then push down on the backwash (BW) handel turn it clockwise 180 degrees to BW and start pump again. Run pump till water coming from BW pipe runs from cloudy to clear. Shut the pump off and pushing down on the BW handel again turn it 180 degrees to filter and start pump again.

Oct 27, 2010 | Pentair Sand Dollar 19" Filter with 1 Hp...

1 Answer

Sand filter putting sand into the pool I've changed gasket,replace head,check latereals,checked the size of the sand we use..still doing it


With these pool filters, there are several things that you need to check if you have sand returning to the pools. First, check your laterals are not broken or cracked. Even the smalled crack can cause this to happen so really inspect them well. Also, your backwash rate could be too high. Try lowering your backwash flow rate and see if this helps. Make sure that your air strainer is not broken or damaged. Replace if it is.

Jun 22, 2010 | Pentair Sand Dollar 19" Filter with 1 Hp...

3 Answers

Can i hook up a intex pump to a sand filter


YES BUT PRICE OF SAND FILTER WILL PROBALLY COST MORE THAN THE POOL ITSELF

Jul 13, 2009 | Intex 2500 Gallon Sand N Sun Pool...

1 Answer

Sand Dollar Filter


If sand is returning to the pool, the most common cause is the laterals, or the internal pipe is not connected to the valve properly.

If you have laterals with "slots" on one side and solid plastic on the other side, the slots have to be installed so that the slots face downward, toward the bottom of tank. If one, or more, are facing upwards, you are pulling sand right into the pool. If you have the newer laterals, with slots on all four sides, one, or more, may not be tightly in place.

If you have too much sand in the filter, that could cause this issue also. Pentair recommends using the #20 Standard Silica Sand in the filters.

Hope this helps!

Jun 13, 2009 | Pentair Sand Dollar 19" Filter with 1 Hp...

1 Answer

Sand from the filter is getting into the pool.


u are getting sand in to your pool most likely because u have a broken lateral i nthe bottom of your filter.

Jun 07, 2009 | Hayward SAND FILTER, PRO SERIES

1 Answer

Not sure how long to run pump


First, RECYCLE is a position that allows water to continue to circulate through the system, BYPASSING the filter. If there is a problem with the system, like an air intrusion/leak, by putting the filter in RECYCLE you can determine if the problem is in the filter, or another part, of your system.

As for how long to run the pump, it can be ran 24 hours a day. Normally, the average run time is 8 to 10 hours a day. Most city codes require that pool water is "turned over" one time daily. This means that all of the water in the pool is ran through the filter at least once a day. Usually, 8 to 10 hours will give you that requirement.

Hope this helps!

Jun 06, 2009 | Pentair Sand Dollar 19" Filter with 1 Hp...

1 Answer

My pool sand filter pump isnt filtering the water


sounds like the sand has clumped together inside filter. you can open filter and replace sand charge or dump into wheel barrow loosen sand and flush clean with hose and put back in

May 13, 2009 | Pentair Sand Dollar 19" Filter with 1 Hp...

Not finding what you are looking for?
Pool & Spa Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top CircuPool Pool & Spa Experts

Jay Finke
Jay Finke

Level 3 Expert

1338 Answers

Bill Jordan

Level 2 Expert

372 Answers

David Spradling
David Spradling

Level 3 Expert

3543 Answers

Are you a CircuPool Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...