Question about Stanley Tools & Hardware - Others

Open Question

Stanley staple gun TRE550 was using it and gun stopped working. I pull the trigger and nothing happens? whats the solution

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 59 Answers

SOURCE: will only shoot one brad and then stops

its problem is too much oil or not enough. never the less, it needs taken apart and cleaned and inspected. make sure you are shooting the right guage and brand hardware. generic doesnt always work.

Posted on May 23, 2009

Ad
  • 1 Answer

SOURCE: staple gun model 0-tre550 keeps stopping when

My electric stapler has quit working. Why would it do that.

Posted on Oct 29, 2009

  • 288 Answers

SOURCE: How do you load nails into a stanley tre550 nail

there should be a button on the bottom rear of the gun, when you press it, it should release a bar that you pull back. the nails go in the dirction you nail them. sometimes the clips are too big for the guns and you have to break about an inch off of them

Posted on Dec 06, 2009

  • 342 Answers

SOURCE: Need help loading staples in my Stanley electric staple/nail gun

there should be a button / lever at the rear press it and it should open so as to insert the staples

Posted on Apr 05, 2010

  • 1383 Answers

SOURCE: stanley bostitch double fires. It is an older

You did not list your model number, however most bostitch nailers use the tva6 trigger valve. As this valve wears it will be erratic. Examine the firing pin that makes contact with trigger. If it looks worn or wabbles from side to side, then time to replace. To remove valve first remove trigger by removing roll with 3MM punch. Next remove one or two roll pins just above the valve, also 3mm. With roll pins removed air pressure will pop out valve. Be carefull because valve can come out with force, use glove or rag to catch. Parts available at www.toolpartsdirect.com, or generic valve at www.ebay.com. Good luck

Posted on Sep 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my Stanley TRE 500 locking up after stapling a short time. What is the + and - on top for? I have lost my manual.


Make sure you are using the right staples for it. This will prevent lockups. You can also try spraying the staple track with a dry silicone lubricant.

The Plus and Minus is to set the strike pressure. Low for cork board, high for oak paneling.

Here is the manual, the TRE550 is close enough.

Stanley TRE550 Electric Staple Brad Nail Gun

Sep 21, 2014 | Electric Stanley Tre500 Staple Gun /...

1 Answer

Does the tre550 have thermal cut out


There is a piece in side the stapler that may have broke as it did with me

Jun 19, 2014 | Stanley Tools TRE550 Electric Staple/Brad...

1 Answer

Been using stapler for past hour suddenley trigger


Could be a bad power cord: broken wire at the switch; a bad switch; the stapler needs lubrication; or the stapler is shot.

Jun 19, 2014 | Stanley Tools TRE550 Electric Staple/Brad...

1 Answer

TRE550 - Stopped working


Check the safer switch that what happen to mine ..I did away with the switch but be careful

Feb 04, 2013 | Stanley Tools TRE550 Electric Staple/Brad...

1 Answer

How do you load nails into a stanley tre550 nail staple gun?


there should be a button on the bottom rear of the gun, when you press it, it should release a bar that you pull back. the nails go in the dirction you nail them. sometimes the clips are too big for the guns and you have to break about an inch off of them

Dec 06, 2009 | Stanley Tools TRE550 Electric Staple/Brad...

2 Answers

How do you load staples into the gun?


The staplesare NOT loaded on top of the pull out shaft; they are inserted directlyinto the slot that opens when you pull the shaft out. If the nose ofthe tool is not placed firmly against a surface, it will not fire.

CLICK HERE
and click the PDF icon on the right of the model # to start the download.

Here is a step by step:
Unplug the tool.
Squeeze the end of the shaft at the rear bottom of the tool and pullout the shaft.
Flip the tool over on it’s back.
Insert the staples,(points up) and then slide the shaft back in.
Plug it in, press the on button (under the the power cord in the back). Press the nose squarely against the material and press the trigger
.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Aug 07, 2009 | Stanley Tools TRE550 Electric Staple/Brad...

1 Answer

Will only shoot one brad and then stops


its problem is too much oil or not enough. never the less, it needs taken apart and cleaned and inspected. make sure you are shooting the right guage and brand hardware. generic doesnt always work.

May 23, 2009 | Stanley Tools TRE550 Electric Staple/Brad...

1 Answer

Have a stanley tre550 and need to know how to use


The staples are NOT loaded on top of the pull out shaft; they are inserted directly into the slot that opens when you pull the shaft out. If the nose of the tool is not placed firmly against a surface, it will not fire. Go to Stanley’s website’s knowledge base and type in the model number, and you can get a PDF of directions. http://www.stanleytools.com/default.asp?TYPE=STATICLEFT&PAGE=Support.htm&LEFT=left_support.htm Below is the graphic from their pdf. Here is a step by step: Unplug the tool. Squeeze the end of the shaft at the rear bottom of the tool and pull out the shaft. Flip the tool over on it’s back. Insert the staples, (points up) and then slide the shaft back in. Plug it in, press the on button (under the the power cord in the back). Press the nose squarely against the material and press the trigger.c901269.jpg

Mar 29, 2009 | Stanley Tools TRE550 Electric Staple/Brad...

Not finding what you are looking for?
Tools & Hardware - Others Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Stanley Tools & Hardware - Others Experts

John Trevino

Level 3 Expert

1383 Answers

yoopertech

Level 2 Expert

131 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Stanley Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...