I sold my car to car max and forgot to take my transmitter or tad that was on the window. They said they don't know where it is. Can I get a new one?

Roll down the windows then lock the vehicle.

After that go to passenger side an attempt to open from inside. Alarm should go off if any.

Don't worry about it , I know the easy way to recover windows password, you can use the software called Smartkey Windows Password Recovery which is easy and effective to operate, and you can download and seethe using method from http://www.recoverlostpassword.com/products/windowspasswordrecovery.html
It can support Windows 8, 7,Windows XP, XP+SP2, XP+SP3, 2000, 2003, 2008, NT, Windows XP Professional x64Edition (64-bit), Windows Server 2003 x64 Edition (64-bit) Operating Systems,Windows VISTA, Windows VISTA(64-bit).I hope it can work out for you.

step one is to replace the battery, you can get new ones at radio shack, walmart, anywhere hearing aid and watch batteries are sold. instructions for opening the transmitter are in the owners manual. if that does not work you may need to take the remote apart and gently clean the electrical contact surfaces with a clean pencil eraser. if that does not work then you need a new transmitter.

TRANSMITTER PROGRAMMING Note: System can learn up to 3 different codes max. 1. Turn Ignition ON and OFF 3 times quickly, leaving it ON the 3 rd time. (ON/OFF, ON/OFF, ON) You should hear (1) short chirp. 2. Push the Program/Override Button for 5 seconds until the siren chirps (3) times. Release the button. The system is now in programming mode. 3. Press Button #1 on new transmitter - siren will chirp to confirm programming. Repeat Step 3 within 5 sec. for up to 2 additional transmitters. 4. Turn off Ignition. Note 1: If only one transmitter is being programmed, continue pressing button #1 until dash LED flashes goes out and the system chirps to exit programming mode to prevent unauthorized codes and noise from entering the system. Note 2: Programming mode is exited automatically after 5 seconds of last code transmission or once 3 new codes have been programmed. The LED will flash (4) times indicating program mode exit.

usually the truck and car fobs work on different signals. you can get inexpensive fobs on ebay, the car fob will have four buttons with a trunk release button.
once you have the correct fob, its pretty easy.

• Just remember that you must also re-program your currently working remotes at this time also as if they are new since prior remotes are erased.
• Max of 4 transmitters can be programmed.

Procedure:

• Keep the driver's door open.
• Electronically unlock the doors (Switch on door or working transmitter)
• 2000-2006: Turn the ignition from OFF to RUN/ON 8 times within 10 seconds, with the eighth turn ending in RUN. If the module has successfully entered program mode, it will lock and then unlock all doors.
• Within 20 seconds, press any button on an transmitter, and the doors will lock and then unlock to confirm that each transmitter has been programmed. Repeat this step for each transmitter.
• NOTE: If the door locks do not respond for any transmitter, wait several seconds and press the button again.
• To exit the programming mode:
• • Turn ignition to the OFF position.
  • Let the 20 seconds expire.
    
  • The maximum number of transmitters have been programmed.

** All transmitters must be programmed at the same time! Max of 4 transmitters can be programmed. **

- Keep the driver's door open.

- Electronically unlock the doors (Switch on door or working transmitter).

- Turn the ignition from OFF to RUN 8 times within 10 seconds, with the eighth turn ending in RUN. If the module has successfully entered program mode, it will lock and then unlock all doors.

- Within 20 seconds, press any button on an transmitter, and the doors will lock and then unlock to confirm that each transmitter has been programmed. Repeat this step for each transmitter.

** If the door locks do not respond for any transmitter, wait several seconds and press the button again. **

- To exit the programming mode:
-- Turn ignition to the OFF position.
-- Let the 20 seconds expire.
-- The maximum number of transmitters have been programmed.
Just remember that you must also re-program your currently working remotes at this time also as if they are new since prior remotes are erased. Hope this helps!

Page 35 of the manual, here is the link to the manual if you don,t have one.

Not all units have transmitters, check the garmin site if in doubt.
https://buy.garmin.com/shop/store/manual.jsp?product=010-00540-00&cID=164&pID=31946

Hope this helps.
Ed

Don't know if you still need this, but the drivers that came with this device are at the following link:
http://instalki.emapa.pl/windows/DRIVERS/Bluetooth/BlueSolei/
Good Luck, Max

Here it is straight from Alldata:

1. Ground pin G of the Data Link Connector (DLC).**Bottom left pin**

• Receiver will respond by locking, and unlocking doors within 2 seconds.

1. Press any button of the first transmitter to be programmed.
2. The control module will respond by locking/unlocking doors and activating rear window release.
3. Press any button of the second transmitter to be programmed (if used).
4. The control module will respond by locking/unlocking doors and activating the rear window release.

1. Remove the ground applied to the reprogrammed connector.

1. Transmitter operation is verified locking and unlocking the doors and activating the rear window release

The TAD (TELPHONE ANSWERING DEVICE) must answer within four rings (the recommended setting is two rings). The MFC cannot hear CNG tones until the TAD has answered the call, and with four rings there are only 8 to 10 seconds of CNG tones left for the fax ?handshake?. message. do not recommend using the toll saver feature on your external answering machine if it exceeds five rings.