Question about Crosman Optics

Open Question

Shot my crosman legacy 1000 last week. Picked it up today, released safety and it won't shoot. Why?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
magoo23
  • 22 Answers

SOURCE: CO2 cartridge leaks down in seconds in a crosman model 357 (older model six shot)

Frank i would love to help you, i'm an airgun enthusiast too. please tell me the model crosman you're shooting at the moment and i would love to walk you through this, if you need repairs i'll also try to help get you in touch with parts or some ideas for service if it's needed.

Posted on May 06, 2008

Ad

SOURCE: Crosman 1377 air pistol

the seal must be broken. send it back to whom you bought it from and get an exchange

Posted on Nov 05, 2008

  • 1383 Answers

SOURCE: Brand new unit. Used last weekend, no problem.

Orings /other parts tend to stick when nailer is new. Dewalt uses some vinyl orings that have been causing premature failure. Be sure to add a few drops of oil when used. Too much oil is not good. Wrong oil will cause orings to swell and cause problems such as yours. Your nailer's firing valve can be reset by rapping the nailer against rubber surface such as a thick rugger mat or coiled rubber air hose. Remove airline and nails, being carefull not to damage the head, rap had against rubber mat and retest gun. If it did not reset rap against nose of gun and test. If no joy, you will most likely need to remove head and manually move cylinder up/down and /or check vinyl orings for failure. Before you try to reset the gun, make sure that the safety is pushing the firing pin all the way in. Air removed, look under the trigger as you push down on safey, if it does go all the way in try bump-firing the gun (for test have nails removed). Hold in trigger and quicky /firmly strike gun against rubber pad. Good luck

Posted on Nov 15, 2010

  • 1 Answer

SOURCE: Crosman 766 was shooting fine, the next shot did

Upon cocking your gun is there the same tension with the cocking spring as there was befor? Also check the condition of your barrel seal for tears or cracks in it.

Posted on Nov 23, 2010

  • 20 Answers

SOURCE: The BBs won't come out or shoot.its a crosman MCSR01 air gun

Seal leak in the air chamber.Need new seals

Posted on Mar 15, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instructions to mount scope


PDF]OWNER'S MANUAL - Crosman

www.crosman.com/pdf/manuals/M4-177-515.pdf

Translate this page There are two different rear sight options for the M4-177 depending on which model you purchase.) Option 1- ... the airgun in any way inconsistent with this manual may make your ... Adjust the rings on your scope to match the measurements of the top rail. ... Toattach the sling at both ends push the sewn webbing loop end.

Crosman M4-177 Multi-pump .177 Pellet Air Rifle Table Top ...

? 24:29
https://www.youtube.com/watch?v=s_0grKCOmX0
May 18, 2012 - Uploaded by Replica Airguns
ReplicaAirguns.com - Crosman M4-177 Pellet-BB Multi-pump Air Rifle ... -Single shot - bolt action with manual advance magazine.... I particularly like the removable iron sights and full rail formounting a scope or red dot sight.

Crosman M4-177: Installing and Adjusting the Sights ...

? 8:38
https://www.youtube.com/watch?v=x8XKOmb41QA
Aug 28, 2012 - Uploaded by Crosman
A detailed look at installing and adjusting the sights for the M4-177 and sighting ... Crosman MK-177 Pellet-BB Multi-pump Air Rifle Table Top ...

Crosman M4-177 shooting rev





Dec 20, 2015 | Crosman M4-177 Air Rifle

1 Answer

Crosman manuals


How can I get an assembly manual for a Crosman air gun model 120 made from 19520to 1654

Oct 19, 2013 | Sport & Outdoor - Others

2 Answers

The BBs won't come out or shoot.its a crosman MCSR01 air gun


Seal leak in the air chamber.Need new seals

Mar 15, 2013 | Optics

1 Answer

I have a crossman 1377 (177) cal pellet pistol. Is it ok to shoot BB'S in this gun? Does it damage the rifling in the barrel? Thanks, Gary


yes it safe to shoot bb,s in the 1377 pump pistol,i have 3 of them they actually shoot true'er and with more vilocity

Sep 19, 2011 | Crosman 1377 177 Single Shot Air Pistol

1 Answer

Crosman 766 was shooting fine, the next shot did not shoot the pellet and just made a funny sound. Now when you pull the bolt back and forth there is no sound to indicate a shot fired when the trigger is...


Upon cocking your gun is there the same tension with the cocking spring as there was befor? Also check the condition of your barrel seal for tears or cracks in it.

Nov 23, 2010 | Crosman Optics

1 Answer

How do you load crosman quest 1000. never owned a break barrel gun before


You load one pellet at a time when the barrel is broken open, the chamber is in the break of the barrel. One stroke, load, close, shoot, keeps you in shape. the old Sheridans, 10 pumps, really kept you in shape.

Aug 12, 2010 | Crosman ® Quest cal. Air Rifle with 4x32...

1 Answer

Crosman 1377 air pistol


the seal must be broken. send it back to whom you bought it from and get an exchange

Oct 22, 2008 | Crosman (4032)

2 Answers

CO2 cartridge leaks down in seconds in a crosman model 357 (older model six shot)


Frank i would love to help you, i'm an airgun enthusiast too. please tell me the model crosman you're shooting at the moment and i would love to walk you through this, if you need repairs i'll also try to help get you in touch with parts or some ideas for service if it's needed.

Mar 23, 2008 | Optics

Not finding what you are looking for?
Optics Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Crosman Optics Experts

Brad Brown

Level 3 Expert

15628 Answers

Anthony Coots
Anthony Coots

Level 1 Expert

6 Answers

raysaw

Level 2 Expert

231 Answers

Are you a Crosman Optic Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...