Question about Echo Garden

1 Answer

Why does my echo cs-352 still running but your not holding the trigger?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Echo Master
  • 34,100 Answers

Could be a defective trigger

Posted on May 03, 2017

Testimonial: "How can i fix it? Thank u"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the oiler adjustment screw on my echo cs-352 chainsaw ?


The oiler is automatic and is not adjustable with a preset flow from the factory.

Jan 17, 2017 | Echo Garden

1 Answer

Can't find the oiler adjustment screw on my echo cs-352 chainsaw


The oiler is automatic and is not adjustable with a preset flow from the factory.

Jan 17, 2017 | Echo Garden

1 Answer

Where is the oiler adjustment screw on my echo cs-352 ?


The oiler is automatic and is not adjustable with a preset flow from the factory.

Jan 15, 2017 | Echo Garden

1 Answer

Need a manual for above


echo air filters do not have a manual nor fuel specs.

Mar 28, 2016 | Echo Air Filter for CS-440, CS-450,...

1 Answer

I have a CS-4400 Echo chainsaw that wont start. I don't think it is firing


1st thing let's check the spark.remove the plug leave it connected to the wire and ground the side of the plug to the engine. and have someone pull the started rope. watch the gap area of the plug for spark. make sure the plug is gap to factory specs, and hold it by the rubber booth. and the on switch is in the run position. good luck Tom

Mar 09, 2015 | Echo Garden

1 Answer

Echo Chainsaw keeps cutting off


does it start and run for a min or two then die try and remove the muffler and run it if ok open the muffler and clean the screen off

May 25, 2012 | Echo Garden

1 Answer

I have an Echo CS-370. For a short while, after the saw was started, the chain would engage a bit (without pressing the gas trigger). I can still get it started, but when the gas trigger is pressed (even...


first question does the chain still spin with out pressing the throttle if it does it is not the clutch sounds like the carb needs to be replaced if that is the problem it would cost about 150.00 depending on the shop labor rate of the shop you take it to im a small engine repair tech..what state do you live in ...email me at whitejeff74@yahoo.com and i will try to help you any way i can to save you some money..if it is the clutch if you are not mechanically inclined it is difficult...

Jul 20, 2011 | Echo Garden

1 Answer

I have an Echo CS-3450 model... The throttle trigger has become disengaged somehow. When I depress it, no reaction from the engine or bar. Any ideas how to fix it?


the trigger is connected to the carb with a linkage rod. it has probably come off. usually you will need to disassemble the saw to get to it. not a easy job. some times best to take it to a shop

Feb 12, 2011 | Echo Garden

3 Answers

How to replace primer bulb on small echo gas chain saw.


I just replaced the primer bulb on my Echo cs-305.
I didn't find the parts list too helpful.

It's easy. All you have to do is remove the air filter and look at the existing bulb from the bottom-- you can reach in with a screwdriver and pop the 'feet' holding it in place off their catches. When I put the new one in, I attached the tubes using a pair of needlenose pliers.

Apr 04, 2010 | Echo 30.1CC Chainsaw With a 14 In.bar and...

Not finding what you are looking for?
Garden Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Echo Garden Experts

Jim London
Jim London

Level 2 Expert

257 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Phil Walker
Phil Walker

Level 3 Expert

605 Answers

Are you an Echo Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...