Where can I find a replacement beater for my breville twin motor mixer model VFP012

EVERYWHERE!

sunbeam mixmaster replacement beaters - Amazon.com

https://www.amazon.com > sunbeam-mixmaster-replace...
Results 1 - 48 of 144 - Univen Mixer Beaters fits Older Vintage Sunbeam Mixmaster Mixers ... Univen Beaters fits Sunbeam Oster Mixmasters Mixer Models 2366, ...

Sunbeam Mixer Parts ' Fast Shipping ' eReplacementParts.com

https://www.ereplacementparts.com > sunbeam-mixer-p...
This is a genuine OEM replacement part, it is sold individually. Most models require two beaters. The overall length of this part is 7-1/2 inches. No tools ...

People also ask

NEW REPLACEMENT SUNBEAM MIXMASTER MODELS ...

https://www.ebay.com > itm
Find many great new & used options and get the best deals for NEW REPLACEMENT SUNBEAM MIXMASTER MODELS 5, 7, 9, STAND MIXER BEATER SET at the best online ...

US$8.25 · ‎In stock

I don't know for certain but that's where the Kitchen Aid one is. Try it, K/A is unscrew to raise the beaters up.

Write to manufacturesrs

Last time I bought them from amazon. Take a look Amazon com replacement beaters, and choose which one fits for you. I hope this was helpful. cheers

where do I find the replacement beaters for the 585r

Call Breville or look on their website at http://www.breville.com/. If you are in the US, call 1-866-273-8455 for replacement parts.

Hi ARADAM, you don’t provide the model number or say if you have a ‘tilt-head’ or a ‘bowl-lift' mixer, which would helpful, but you can easily download a PDF version of your Owners Manual from the KA website at: (http://www.kitchenaid.com/flash.cmd?/#/page/home).
Click on Customer Care>Locate Manuals& Guides> and enter the 6 character model number and select a file listed under Owners Manuals and save that file to your PC. You’ll need to have Adobe Reader to be able to open it. Turn to Page 11 and you will find the instructions for adjusting the mixer head height. I have extracted the instructions below:
Beater to Bowl Clearance
Your mixer is adjusted at the factory so that the flat beater just clears the bottom of the bowl. If for any reason, the flat beater hits the bottom of the bowl or is too far away from the bowl, clearance.
Tilt-Head models
• Unplug mixer.
• Lift motor head.

• Turn screw (A) SLIGHTLY counter clockwise (left) to raise flat beater or clockwise (right) to lower flat beater.
• Make adjustment with flat beater, so it just clears surface of bowl.
If you over adjust the screw, the bowl lock lever may not lock into place.

Bowl-Lift models
• Unplug mixer.
• Place bowl lift handle in down position.


• Turn screw (B) SLIGHTLY counter clockwise (left) to raise flat beater and clockwise (right) to lower flat beater.
•Make adjustments with flat beater, so it just clears surface of bowl.
If you find the adjustment screw missing, you’ll need to replace it. But now you’ll need
I hope this helps! –Howard, Burke, VA
If this solution has helped you, please rate it, thanks! - hslincoln

many of the beaters are available online. There are replacements available for the mixmasters.
Check for your specific model HERE...

Merry Christmas to you..

Hi, KLOEHR, your beater will not lengthen by losing a screw. However, if you lost your Beater to Bowl Clearance adjustment screw, then it might appear that your beater had ‘grown’ because now the beater may be touching the bottom of your mixing bowl, where previously it had not. Simply said, the beater didn’t grow the mixer head drooped.
You don’t say if you have a ‘tilt-head’ or a ‘bowl-lift' mixer, but you can easily download a PDF version of your Owners Manual from the KA website at: (http://www.kitchenaid.com/flash.cmd?/#/page/home).
Click on Customer Care>Locate Manuals& Guides> and enter the 6 character model number (in your case, use KSM5PS)and select the last file listed that appear under Owners Manuals: KSM5PSWW0.pdf (2930.74 KB) and save that file to your PC. You’ll need to have Adobe Reader to be able to open it. Turn to Page 11 and you will find the instructions for adjusting the mixer head height. I have extracted the instructions below:
Beater to Bowl Clearance
Your mixer is adjusted at the factory so that the flat beater just clears the bottom of the bowl. If for any reason, the flat beater hits the bottom of the bowl or is too far away from the bowl, clearance.
Tilt-Head models
• Unplug mixer.
• Lift motor head.

• Turn screw (A) SLIGHTLY counter clockwise (left) to raise flat beater or clockwise (right) to lower flat beater.
• Make adjustment with flat beater, so it just clears surface of bowl.
If you over adjust the screw, the bowl lock lever may not lock into place.

Bowl-Lift models
• Unplug mixer.
• Place bowl lift handle in down position.

• Turn screw (B) SLIGHTLY counter clockwise (left) to raise flat beater and clockwise (right) to lower flat beater.
•Make adjustments with flat beater, so it just clears surface of bowl.
If you find the adjustment screw missing, you’ll need to replace it. But now you’ll need
I hope this helps! –Howard, Burke, VA
If this solution has helped you, please rate it, thanks! - hslincoln

Pry the beater release button out with a screwdriver. There are two screws underneath it and one under the motor housing between the the beater holes. This will allow you to remove the chrome front cover, but not the motor and drive assembly. Getting to the part that contains the gears requires complete disassembly of the mixer. It is not designed for service, and requires patience and a variety of tools to disassemble.

It has a metal worm gear and plastic drive gears. If the beaters are out of alignment, then one or both of the plastic gears are stripped and the mixer is junk. Repair plus shipping costs equals the price of a new mixer. This is the weak point of these mixers and a fundamental flaw in an otherwise robust and sturdy design. It is definitly not the same mixer *********** bought 30 years ago.