Question about Dishwashers

1 Answer

Is there a water and sanitation degree at university of pretoria

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 3,828 Answers

Posted on May 01, 2017

Testimonial: "thank"


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a LXiC Hobart dishmachine I do not want to use Sanitizer because my hot water is very hot. How do you disable the sanitizer pump and alarm? H.

Do you realize that to sanitize with hot water alone requires 180 degree F water? I am a hobart technician and I've never seen any business or residence with hot water anywhere near that. Residential hot water is generally approx. 120, Commercial locations generally use approx. 140, but never near 180 (tap water that hot would be a severe safety problem). Hobart LXIH machines use a built in booster heater to boost the temperature of the incoming hot water up to the required 180 deg.

Jul 01, 2011 | Hobart 24 in. LXIC-5 Built-in Dishwasher

1 Answer

Rinse temp too low, first it comes up to 180 degrees and then drops to wash tank temperature, WHY?

The rinse temp only reaches 180 degrees for a couple of seconds towards the end of the cycle. This will sanitize all warewash and meets most health code regulations. The rinse water temp will drop rapidly as it is incorporated in to the machine and sprayed on the dishes.

Feb 23, 2010 | Moyer Diebel 24 in. 301HT-40 Built-in...

3 Answers

After pressing On - the dishwasher just sits are about 80 degrees and doesn't get any hotter when normally it goes up to about 118. Can we still use it to wash or is something wrong?

A hobart LXIH-3 uses a chemical to sanitize however a 120 degree wash temp is required as well.

Turn up your hot water tank that supplies the dishmachine, make sure your sanitizer is pumping into the rinse cycle using micro-clorine test papers and all is well.

Dec 22, 2009 | Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

Why sanitize button?

no, no home d/w will ever sanitize dishes, to sannitize dishes the rinse water has to be @180 degrees or above , only 1 d/w had that capability which was the old kitchenaidmod. which hobart produced for them

Oct 25, 2009 | Dishwashers

1 Answer

What is the sanitation cycle for on Model

Typically "sanitation" cycles require hot water....then they add more heat to the washer during the cycle. It is not 212 degrees, but it is very hot and does kill most germs.

The mildew smell is normally caused by water remaining in the system lines - because the water drain pipe is too high and keeps too much water inside after the system pumps the interior pan. Suggest that you just pour in some bleach after the last load...that should kill all mildew. Please do not overdo it. Only about 1/8th to 1/4 cup is needed to keep the mildew smell under control

Oct 11, 2009 | Washing Machines

3 Answers

Hobart 24 in. LXIC fails sanitizer tests. The sanitizer pump is pumping out about 4-5 ml per rinse when I remove the tube at the 90 degree tube fitting. According to specs it should be about 3 ml of 8.5%...

I thought it was designed for domestic bleach at 5.25%, and looking for a solution of 50 ppm of sanitizer and rinse water. Either the elbow is blocked, or the silicone tube in the pump has collapsed. Use rubber gloves and face protection when working on chemical tubing.

Jun 29, 2009 | Hobart 24 in. LXIC-5 Built-in Dishwasher

1 Answer

Kenmore model 587 - HO flashing - what does this mean?

It means the dishwasher is on hold till the water temp reachs 160 degrees to sanitize them nasty dishs Kimosabe.

Apr 09, 2009 | Dishwashers

1 Answer

Hobart LX30H washing to hot.

what temp is it washing at. washing should not be the problem. This machine is designed to rinse at 180 degrees + to sanitize dishes. The machine could be converted to a chemical sanitize, it would use bleach in the rinse water instead of 180 degree water to sanitize.

Sep 04, 2008 | Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

Dishwasher not working again

is the clean light blinking, if so make sure water temp is at least 120 degrees

Jan 02, 2008 | Kenmore 24 in. 15933 Built-in Dishwasher

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers


Level 3 Expert

77939 Answers

Brad Brown

Level 3 Expert

16841 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides