Question about Car Audio & Video

Open Question

I did downloaded the manual for lark 1 scooter and i got 3 blank pages

So i still need to know how to hook up the 2 batteries with 1 red wire and 3 black wires

Posted by on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 36427 Answers

SOURCE: need a manual for a lark 1 scooter. have to remove 2 batteries, and there is 1 red wire and 3 black need to know how to hook up both batteries with 1 red wire and 3 black wires

Try Googling (lark)(1)(manual) without parens.

Posted on Apr 30, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Looking for info on Lark 4 (user manual)

regrettably this is the only thing I can find. I can't even find the manufacturer website!

you could ask here on the contact page.

Jan 24, 2016 | Health & Beauty

1 Answer

Lark 4000 XL manual

Download schematic wiring diagram lark 4000 xl - Google ... Google Docs, Sheets, and SlidesLooking for schematic wiring diagram lark 4000 xl? Download schematic wiring diagramlark 4000 xl. schematic wiring diagram lark 4000 xl. User Manuals ...

Sep 26, 2015 | GPS

1 Answer

Lark 3. Where can I get a wiring diagram?

hi , you won't get a lark 3 diagram sadly

If you tell me the controller used or better a picture (black box located at the rear ) i can help , sometimes it hard wired by a switch from batteries or the controller outputs a voltage to the lift motor ,

I have repaired many Larks...


Jun 08, 2015 | Health & Beauty

1 Answer

Charging schematic for pride scooter

red + goes to pin 1, black - goes to pin 2 and jumps to pin 3

Dec 29, 2013 | Pride Rally 3 Wheel Scooter

1 Answer

Our Liteway scooter has been unused for a couple of years. We purchased a new battery and charged it up but it won't run. The freewheel device is in place and we've done all the troubleshooting we know per...

terry, did you replace both batteries? If you did check your wiring connections on the batteries. Make sure that the polarity of the wiring is correct( red to positive and black to negative) and if you replaced just one battery then you have to replace the other one also. Once you have 2 new batteries installed and have made sure the wiring is correct. Turn on the scooter and see if you still get the flashing lights look at your manual and see that the 3 flashes mean a short between the batteries and the motor. If you continue to get the error you will have to contact your local provider or a service company to check the scooter.. Hope this helps

Sep 28, 2010 | Golden Technologies Health & Beauty

2 Answers

I needto replace the battery charger on my Rascal 600F scooter

Hi. Most chargers with only two wires, have a small bridge wire from the
black ( negative ) wire to the middle terminal of the connector. This disables the controller while the machine is charging. The charger will still work without this bridge wire, but the scooter will still operate normally.
There are a few different chargers around that have an internal relay that disables the scooter, but these chargers are normally "on-board" chargers.
Good luck. Neil.

Jul 05, 2010 | Electric Mobility Power Electric Scooter...

1 Answer

Model# RR100 MFG Code 27046B, got 2nd had with no manual. How do I hook up the new batteries? So many terminals to choose from?

Hi.The best idea if you are not to sure, is to get help. If you want to do it your self, be careful, batteries can be dangerous if shorted out.
Each battery has a positive ( red ) terminal, and a negative ( black ) terminal.
Change one battery at a time, make sure the scooter is turned off and /or unplug the battery leads.
The red wire will go to the red terminal ( positive ) onthe battery, the black wire to the black terminal.
Each battery should have 1 black wire and 1 red wire to it.
Remember, be careful.Neil.

May 30, 2010 | Pride Mobility Victory 3 Wheel Electric...

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4874 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers


Level 3 Expert

76846 Answers

Are you a Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides