Question about Radio Communications

Open Question

I have a bluetooth headphones Qy7,Previously it used to blink blue and red when left for charging now its blinking only blue but now after leaving it charged for a day also its not getting charged.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: Not getting Charged

If you mean the Insignia NS-BTHDST or NS-BTHDP, I read elsewhere in this forum that you can reset it and that might work. See the manual. Basically you hold the volume up and volume down together while the charger is plugged in. The instructions were vague and mine did not reset nor show a purple light as indicated in the manual.

However, after trying that a couple of times, I accidently got it to work by pressing the phone/play button twice. Press it normally, not the long press you use to turn it off and on.

So in other words, plug it in to the charger. Press and releas play. Press and release play.

For me, the charge light turns on and it starts charging. I hope this helps.

Mine is new too, sort of. It was an "open box" from an ebay seller. I may return it anyway, since it is clearly NOT behaving correctly. You shouldn't have to press buttons at all to get it to charge. I know because I have another one.

Bon chance, mon ami.

Posted on Oct 31, 2008

Ad
  • 124 Answers

SOURCE: battery light blinking red during charging

Dell or Panasonic? Your post has both listed.

If the blinking light on a Dell is yellow or amber or orange (somewhere in that color range) and continues to blink the entire time it is plugged into AC power (wall outlet) and when you unplug it from the wall the laptop immediately dies .... then you battery is dead and needs replaced.

If the blinking light stops after a while (perhaps a minute?) and then turns green while plugged into AC power, then it is successfully charging - or so it thinks.

When you unplug it from the wall, does it stay up and running?
If it runs, it's OK - just ignore the light and plan on getting a new battery one day, start browsing now. :)
If it dies immediately upon unplugging, then your battery is dead and needs replaced.

Posted on Jun 13, 2009

  • 14 Answers

SOURCE: Makita BR1815 li-ion batteries won't charge

your batteries are toast;must replace

Posted on Aug 02, 2009

  • 23 Answers

SOURCE: My motorola h721 keeps blinking red.

if you didn't pair your phone up yet, that could be why. Hold all 3 buttons down for 10 sec. should go solid blue, then pair your phone cause its in discovery.

Posted on Aug 19, 2009

  • 1 Answer

SOURCE: I went to charge my motokr s305 headphones and the

I called Moto Tech Support. They are sending me a replacement. They did not seem to have any troubleshooting ideas for the blinking red light.

Posted on May 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What if my uproar wireless headphones are flashing red and blue ?


The headphones flash blue when u switch it on.If it flashes blue and red, it means that it is in bluetooth connection mode.So u can connect it with bluetooth devices by switching on bluetooth on your phone or pc.After connecting the red light stops flashing automatically and blue light starts blinking.Hope you understood. :)

May 04, 2016 | Audio Players & Recorders

Tip

Colour full BlackBerry ..If you are a Blackberry user.You must read this


In BlackBerry LED indicator blinks in different colors to deliver different notifications to the user:

Blinking RED: The LED indicator blinks red whenever you have incoming or waiting communication messages on your phone - new email, new call or missed
call,

Blinking GREEN: this is Coverage Indicator light. This lets you know you are connected to a network.

Blinking BLUE:If your phone is connected to a Bluetooth device, such as a Bluetooth headset it blinks blue.

Blinking YELLOW: A blinking yellow light means it is time to charge your BlackBerry

on Dec 15, 2009 | Cell Phones

1 Answer

Why is my hv-800 headphones blinking red and blue?


Probably because they are Bluetooth headphones and somehow they got put in 'pairing' mode and are now scanning/searching for a compatible Bluetooth audio device (phone, tablet, computer, etc.) to pair and connect with.

Oct 15, 2014 | Audio Players & Recorders

1 Answer

When I plug up the bluetooth to charge the red light appears then it blinks blue red does that mean it is charging or not because it is not working with phone


That might meaning that's it's draining the residual charge left on the battery, before it can be charged, but if it does this for more than an hour, your battery is "toast".

Aug 28, 2014 | Universal QuickCell Q7 Bluetooth Headset -...

2 Answers

Why wont kinivo bth220 wont link with my phone no matter what i try


Can you confirm if you are able to put the BTH220 headphones in pairing mode. Please try the following steps and see if works:
  1. Make sure that the headphones are fully charged.
  2. Switch off the headphones.
  3. Put the headphones in pairing mode by pressing the MFB button (center) for 7-10 secs till you see the red and blue LED blinking alternatively. Please do not leave the button as soon as blue LED appears.
  4. Follow the operating instruction of your Bluetooth device to start the pairing process.

Sep 29, 2012 | Kinivo Bth220 Bluetooth Stereo Headphone -...

1 Answer

Kinivo bth220 wont link


Can you confirm if you are able to put the BTH220 headphones in pairing mode. Please try the following steps and see if works:
  1. Make sure that the headphones are fully charged.
  2. Switch off the headphones.
  3. Put the headphones in pairing mode by pressing the MFB button (center) for 7-10 secs till you see the red and blue LED blinking alternatively. Please do not leave the button as soon as blue LED appears.
  4. Follow the operating instruction of your Bluetooth device to start the pairing process.

Sep 29, 2012 | Kinivo Bth220 Bluetooth Stereo Headphone -...

1 Answer

How do I pair insignia bluetooth headphone with Ipod touch When I have my ipod search for bluetooth devices, it acts as if it does not see the headphones.


The Insignia headphones must be set to "pair".

With the headphones off, press and hold the power button on the headphones until the logo starts blinking red/blue. You are now in "pair mode". Have your Touch look for bluetooth devices and it should see it now.

Hope this helps!

Mar 29, 2010 | Insignia Bluetooth Wireless...

1 Answer

I have a wireless headphones the only number i can see is model f0461b on the trasmitter. The transmitter and headphone are not comunicating the lights are red not blue.How do i recalibrate them so they...


In rare cases, the FreePulse Headphones may loose synchronization with the receiver. If this occurs the following steps will re-establish the connection by putting both the headphones and the receiver in discoverable mode (actively searching for another bluetooth device it can connect to).
Putting the headphones in discoverable mode:
Press and hold the power button (located next to the charging port on the right earpiece) on the headphones. The LED on the button will go through three states in this order:
  • Blinking Red
  • Off (continue to hold. the LED will be off for several seconds)
  • Alternately blinking red and blue. (The headphones are now in discoverable mode and you can release the button at this point. The headphones will remain in this state for 30 seconds).
Putting the receiver in discoverable mode:
Press and hold the power button (located on the side of the receiver opposite the headphone jack).The LED on the button will go through three states in this order:
  • Blinking Red
  • Off (continue to hold. the LED will be off for several seconds)
  • Alternately blinking red and blue. (The reciever is now in discoverable mode and you can release the button at this point. The reciever will remain in this state for 30 seconds).
Re-establishing the connection:
To re-establish the connection between the headphones and the reciever, put the headphones and the receiver in discoverable mode at the same time. It will take a few seconds for the two devices to establish the connection. Once the connection has been established the LEDs on both the headphones and receiver will glow solid blue.

Nov 19, 2008 | Audio Players & Recorders

2 Answers

My logitech headphones dont turn on anymore.


Quote from LOGITECH official site:
In rare cases, the FreePulse Headphones may loose synchronization with the receiver. If this occurs the following steps will re-establish the connection by putting both the headphones and the receiver in discoverable mode (actively searching for another bluetooth device it can connect to).  
Putting the headphones in discoverable mode:
Press and hold the power button (located next to the charging port on the right earpiece) on the headphones. The LED on the button will go through three states in this order:
  • Blinking Red
  • Off (continue to hold. the LED will be off for several seconds)
  • Alternately blinking red and blue. (The headphones are now in discoverable mode and you can release the button at this point. The headphones will remain in this state for 30 seconds).
Putting the receiver in discoverable mode:
Press and hold the power button (located on the side of the receiver opposite the headphone jack).The LED on the button will go through three states in this order:
  • Blinking Red
  • Off (continue to hold. the LED will be off for several seconds)
  • Alternately blinking red and blue. (The reciever is now in discoverable mode and you can release the button at this point. The reciever will remain in this state for 30 seconds).
Re-establishing the connection:
To re-establish the connection between the headphones and the reciever, put the headphones and the receiver in discoverable mode at the same time. It will take a few seconds for the two devices to establish the connection. Once the connection has been established the LEDs on both the headphones and receiver will glow solid blue.

Do this and Freepulse will be pleased.

Aug 15, 2008 | Logitech FreePulse Wireless Consumer...

1 Answer

Free Pulse


The following procedure will re-establish the communication link between the Headphones and the Wireless adapter, this is called "pairing". Before you start please make sure both the headphones and the wireless adapter are fully charged and turned off.
Note: The headphones and the wireless adapter come pre-paired from the factory.
1. Press and hold the power button on the headphones. See Figure 1.
headphone.jpg
Figure 1

2. Continue to hold the button down until the LED starts flashing red/blue in an alternating pattern. Release the button when the LED starts flashing red/blue. See Figure 2.
headphone-flash.gif
Figure 2
3. Once the headphones LED is flashing red/blue, press and hold the power button on the wireless adapter. See Figure 3.
receiver.jpg
Figure 3
4. Hold down the button until the LED starts flashing red/blue in an alternating patter. The LED will blink blue, then turn off for a few seconds then blink red/blue. Release the button when the LED starts flashing red/blue. See Figure 4.
receiver-flash.gif
Figure 4
5. Once both the headphones LED and the adapter LED is blinking red/blue, press the volume up button once on the headphones. See Figure 5.
headphone-volumeup.jpg
Figure 5
Once the headphones is paired with the adapter, the LED on the headphones will blink blue once every two seconds. See Figure 6.
headphone-flash2.gif
Figure 6
When the adapter is paired the LED will be solid blue. See Figure 7.
receiversolid.jpg
Figure 7
The adapter may continue to blink red/blue for a few seconds even after the headphones LED starting blinking blue. This is normal; the adapter may take a few additional seconds before the LED turn solid blue.
Once the headphones and the adapter are paired, it is not necessary to pair them again even if the batteries on both units are completely drained.
Additional Note: Repeated pairing will not improve the sound quality or give the headphones and the adapter a cleaner connection.

Mar 11, 2008 | Logitech FreePulse Wireless Consumer...

Not finding what you are looking for?
Radio Communications Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Radio Communications Experts

eradiostore
eradiostore

Level 3 Expert

1654 Answers

Brad Brown

Level 3 Expert

15756 Answers

Mike Charette

Level 3 Expert

1795 Answers

Are you a Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...