Question about Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

Open Question

Wiring schematics for a Kenmore Elite heating Element can style. I have it all back together with new element now cant remember where 6 wires on the outside of casing plug into which ones?

I have ^ place to plug and six wires I do not know where the go on the heater can

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Master_Tech
  • 770 Answers

SOURCE: HE 4 Removing Heating Element

post your email i will send you the manual on it.. also post the complete model number from the unit

Posted on Jan 26, 2008

Ad
  • 1028 Answers

SOURCE: Kenmore Dryer Model 110 Heating Element & Thermostat

believe that model has a relay under console..pull console end caps off remove screw on each end roll console back..if your model has an electronic bd it also has a heat relay it will be the one with 2 large red wires.. a quick ck would be to unplug power remove the red wires and tape bear ends together pug back up turn on dryer if it heats unplug and exchange the 2 relays the one with the blue wires is the motor relay and is same as heat relay try again if motor fails to start bad relay if motor starts bad control bd

Posted on Aug 10, 2008

jmgldsmth
  • 1889 Answers

SOURCE: Installing Heating Element 279838 on Kenmore Dryer 110.66662500

go to: searsparts on the web put in your model# and look at the exploded views and, schematics

Posted on Apr 22, 2009

  • 478 Answers

SOURCE: Kenmore 62064 elec. drying is runing (all buttons

Hi Sam,
Make sure that you have checked the circuit breaker, to find out wither or not the breaker was tripped or not, before you take it apart. but there is a good chance that you are right on the money......

Posted on Dec 12, 2009

  • 189 Answers

SOURCE: Lower Heat Element in Kenmore Oven

Hey- Disconnect power. pull back cover to access wires for element. Re-connect wires and loosely re-position insulation. Reinstall back cover and chk operation.- Hope this helps- ED

Posted on Feb 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dryer is not heating. How can I tell if it is the fuse, heating element or thermostat? Already went through all the troubleshooting mentioned in the handbook.


If it's running but not heating odds are the wire to the heating element has broken. They had a habit of "cooking" themselves near the junction block. Unplug the unit and follow the electrical supply into the machine. Dis-mantle as necessary provided you're comfortable knowing that you can put it back together. Once you find the heating element look where the electrical supply wire attaches. It's a good bet you'll find the problem there if it's a broken wire.

Mar 14, 2015 | Kenmore Dryer Sears Elite

Tip

How to change the Heating Element in a Kenmore Elite Electric Dryer?


If the dryer is running but not heating,then the heating element needs to be replaced. The procedure is as follows:--- 1) First of all unplug the dryer from wall outlet.
2) Remove the front service panel of the dryer.
3) After the front service panel is removed. You will see the heating element wires and heat shield.
4) Remove the heat shield by plucking the wires out from the heat shield.
5) Also remove the screws holding the heating element.
6) The heating will have to be moved a bit to come out easily. Before removing the heating element out. Please note down the position of old heating element. So while placing the new heating element you don’t face any problem.
7) Replace the element with a new element.
8) Refit all the parts removed while removing the old heating element properly.
These will help. Thanks.

on Mar 20, 2010 | Dryers

2 Answers

Kenmore Elite Gas range, model # 790.79363401 The range works but the oven does not seem to heat up. It appears to ignite, just not get hot.


Hello,

the problem should be from the heating element of your Kenmore Elite Gas range. The heating element is either defective or may have loosed contact as a result of heat coming out of the Oven. The heat coming from the oven may have melted the wire connected to the heating element which might not make it heat up.

Disassemble the oven and check if its actually the wire connected to heating element that got melted, or its time to replace the heating element.

Good luck.

Dec 15, 2010 | Kenmore Ovens

1 Answer

Dryer starts but no heat. Am I correct in assuming heating element is the only problem?


Its usually not the element
Check 220 voltage at wall it will run on 110 but not heat
Check breaker
Check thermal fuse at top of element case in back
2 wires
But check element anyhow

Jul 07, 2010 | Kenmore Elite HE4 Electric Dryer

1 Answer

My Kenmore elite electric dryer will not heat. I


Hi


Thanks for using FixYa. No Heat issue in an electric dryer is usually caused due to three things mainly: Thermal Fuse, Wiring Harness and/or Heating Element. Start with checking the Thermal Fuse which is mounted inside the back cover panel to the exhaust duct and is mounted in white plastic housing. If that’s fine then the Heating Element should be checked. Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Jun 03, 2010 | Kenmore Elite HE4 Electric Dryer

1 Answer

My Kenmore Elite dryer just quit heating up...is it the heating element or possibly a fuse? The lint trap had qite a bit of lint in it..maybe it just over heated and blew a fuse?


There is a thermal sensor attached to the housing of the heating element, you can check the thermal sensor by jumpering the two wires to the thermal sensor together, and then run the dryer and see if the heating element is now working, if the dryer is now heating up then replace the thermal sensor.

May 10, 2010 | Dryers

1 Answer

Kenmore elite elec dryer, 110.64972300. runs no heat


Pull one wire off the element and start the dryer in a heat cycle . Check power from that wire to the cabinet . Touch the meter to the terminal you pulled that wire off of , and check that voltage . You cannot get correct voltage by checking across the element . Trace the wire NOT getting 120 volts . It will either go to the timer or motor . It will lead you to the problem .

Apr 28, 2010 | Kenmore Elite HE4 Electric Dryer

1 Answer

How to replace a heating element for a kenmore


Hello there
i am posting instruction for this dryer below
(For some help with that, and before buying an element you might not need, please see my article entitled 'The No-Heat Dryer'). Note: Always check airflow out the vent before firing up your dryer with its new element. A partially clogged vent can burn out an element - even a brand new one - fast! Just run the dryer on the 'no-heat' or 'fluff' setting, then go outside and check for a good strong flow of air from the vent hood. If there's any doubt, Whirlpool makes a cool little airflow test kit for their dryers that will tell you for sure, from inside.
There are basically 3 styles of heating elements in use for these dryers.
1) Most common is the 'long' one, part number 4391960, accessed from the back of the dryer, and which looks like this:
wpl%204391960%20el.jpg To replace this one, power down and pull the dryer out and remove the back cover. You'll see a long, vertical 'can' on the right side, with the element coil inside. To remove this can, simply pull the element wires (can be hard to remove; I use a long-nosed pliers), the limit thermostat wires just above them, and the thermal fuse wires if equipped (this is a little device mounted high on the side of the can, with two wires attached). One 5/16" hex screw at the top and a little strap holds the can in place. Remove this screw (You can look through the small hole that lines up with it, originally to poke a long screwdriver through), tip the can rearward, and lift it off its two bottom hooks. Once the can's out, one screw holds the element inside. Remove it, and the old element coil will slide out. Slide the new one in, reverse this process, and you're done!

Nov 13, 2009 | Kenmore Dryers

1 Answer

Kenmore Dryer Model 110 Heating Element & Thermostat


believe that model has a relay under console..pull console end caps off remove screw on each end roll console back..if your model has an electronic bd it also has a heat relay it will be the one with 2 large red wires.. a quick ck would be to unplug power remove the red wires and tape bear ends together pug back up turn on dryer if it heats unplug and exchange the 2 relays the one with the blue wires is the motor relay and is same as heat relay try again if motor fails to start bad relay if motor starts bad control bd

Aug 09, 2008 | Kenmore 63942 Dryer

Not finding what you are looking for?
Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103 Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dishwashers Experts

Ken Johnston
Ken Johnston

Level 1 Expert

56 Answers

Fred Sops

Level 2 Expert

272 Answers

D. E. Hev

Level 3 Expert

1179 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...