Question about Garden

1 Answer

Diagram for 123k05-0478-e1 carburetor - Garden

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 11 Answers

Posted on Apr 28, 2017


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


I don't have much experience with Stihl products but I do have a couple of disc cutters, both of which had a short life and suffered piston damage.

I suspect the air cleaner isn't as efficient as it should be.

Apr 26, 2017 | Stihl Garden

1 Answer

Intek 12.5 HP. 219907-0131-E1. Idles fine but won't rev. Sputters when trying to increase speed.

If you are using gasoline that has alcohol in it, (and most do) then it can affect the float in carburetor. If you have a plastic float, it can sink. The other things to check are the needle valve and the seat.
Here is the diagrams for that:

Mar 29, 2017 | Garden

2 Answers

Schematic acer aspire -e1-571g

Due to the complicity of multi layer boards, schematics are not available. Manufacturers agree that if a motherboard fails under warranty, it is replaced, not repaired, so no need for schematics.

Nov 19, 2015 | Acer Computers & Internet

1 Answer

Crankcase is full of fuel


The float and needle valve in your carburetor are not working as they should. The float should force the needle valve into the carburetor body to stop the flow of gas when the float bowl is full. When the float and needle valve do not work as they should, the gasoline keeps flowing into the float bowl and into the carburetor, and into the cylinder where it flows past the piston rings and into the crank case.
The carburetor needs to be removed and cleaned.

May 15, 2015 | Briggs & Stratton Briggs Stratton Vanguard...

1 Answer

What causes a lot of gas in oil on 8.5hp B&S

This would be caused by a sticky needle valve on the float in the carburetor.You have three cures 1. remove and clean the carburetor internally. 2. replace the carburetor with a new one. 3. or most simply buy and install a fuel shut off valve and turn it off when not in use. make sure you change the oil 1 4 ID LINE GAS FUEL SHUT OFF VALVE TECUMSEH BRIGGS

Jun 03, 2014 | Briggs & Stratton Briggs Stratton Intek V...

1 Answer

Where can I view a diagram of carburetor 699807?

Parts and Diagrams for Briggs and Stratton 407577 0292 E1 Don't know if this will help you, but is a parts breakdown of the part number. Hopefully it matches yours.

May 06, 2014 | USAF Security Forces Shield Decal

2 Answers


Go to this LINK and find the part/diagram that can help you.

Nov 04, 2010 | Briggs & Stratton Briggs Stratton Intek V...

1 Answer

I need a diagram of a 1993 mazda mx3 cooling system.

check in E1 or E2 (V6 or I4) in the workshop manual for the diagram.

Apr 16, 2009 | 1993 Mazda MX-3

Not finding what you are looking for?
Garden Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2478 Answers


Level 3 Expert

708 Answers

john h

Level 3 Expert

15387 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides