Question about Kipor Electrical Supplies

Open Question

I have kipor generator serial number KDE 480 ss3 I want know what is error 27 on digital control panel please help me

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 86 Answers

SOURCE: error code 27

The error code p27 the toner density sensor unplugged/dirty/faulty
Any problems please get back to me
thank you

Posted on Feb 19, 2008

sal_kh_sab
  • 98 Answers

SOURCE: KIPOR KDE 6700TA 5KVA Generator

forget about the display read the manual and find out how many volts are needed to charge the battery....then
get a voltometer and disconnect the terminals from the battery and connect them to the voltometer while the generator is running...
find out what the reading is...if the reading is zero (0)...then post a problem on (no out put)...
if not.....then there has to be a mistake...
if it reads a voltage thats too low..then you AVR card is burnt out (AVR card is located in the other end of the generator (beyond the stator-side cover)...

Posted on Oct 25, 2009

Testimonial: "Khan sb. truly is a professional. "

toolkits
  • 1099 Answers

SOURCE: KitchenAid refrigerator, Model number: KSSO48FTX00 Serial Number:

Hello,
Sounds like you have a defrost problem since the freezer side is working okay . It probably is not blowing cold air into the refrigerator side , so to check the defrost circuit , unplug the refrigerator and inside the refrigerator section at the top about 2" in from each side in the back , there are "D" slots to put a finger in , and pull downward and forward , to remove the control panel cover . Once removed , there is a 1/4" screw on each side holding the adjustment indicator panel on , 1 phillips screw behind both light bulbs , and 1 screw holding the complete panel to the rear wall . After removing these 5 screws , at the top right corner , with about 6-8 wires going to it , is the adaptive defrost board . Sometimes you can see the electronic board and on newer refrig's , a white box will be seen. Inside this box , is the adaptive defrost control . Disconnect the plug going to the board and on the right side of the PLUG , the far right wire is yellow , then another color , then white . Useing a small insulated wire with both ends stripped , insert one end into the yellow wire hole and the other into the white wire hole . This will bypass the adaptive board and send power directly through the defrost bimetal ( thermostat ) AND heater to check if they are good .Plug the refrigerator back in . Now , wait about 3-5 min and look for a red glow at the bottom of the inside freezer panel , which will be the defrost heater or listen for sizzling which will be the frost melting and dripping onto the heater .If NO red glow , watch for a spark while removing the jumper wire you installed , from the plug . If a spark IS seen , then the heater was on and the heater AND bimetal are good . If you see the red glow , hear the sizzling , or see the spark , then the adaptive defrost board should be replaced . If no glow , sizzling or spark , then unplug the refrigerator and reinstall the refrigerator control section .
Remove the food in the freezer section enough so that the 2 screws holding the lower freezer panel on and the freezer panel , can be removed . Remove the panel . If the heater (black element at the bottom of the coils ) wires are visible , trace then to the top of the coils and disconnect . Use an ohm meter to determine if the element is good . If the element IS good , at the top of the coils , is a 1" cylinder with 2 wires , clipped onto the coils . This is the defrost thermostat ( bimetal ) . Replace this part if the element shows good . If the element shows bad , replace the element . NOTE 1 : sometimes the element and the bimetal come wired together and the replacement part comes with a new heater and bimetal already wired together . This would be the advisable replacement part . However , each part can still be replaced individually . NOTE 2 : If looking at the bimetal and the top plastic " cap " looks cockeyed , replace the bimetal as moisture has gotten inside and disturbed its designed function .

Take care in solving the the problem....

Posted on Oct 04, 2010

  • 93 Answers

SOURCE: Hi, I from Indonesia and I need help... I have

maybe your generator has a problem with the cylinder head gasket.try to remove the cylinder head gasket,grind the valves intake and exhaust it. use the gasket cement to glue the cylinder gasket then assemble it

Posted on Feb 24, 2011

  • 132 Answers

SOURCE: serial number miller AEAD 200LE JF 885778

Check this out:

http://www.ebay.com/itm/MILLER-AEAD-200LE-CONSTANT-CURRENT-AC-DC-ARC-WELDING-GENERATOR-GAS-POWERED-/310368057796?pt=BI_Welders&hash=item484360b9c4

Posted on Jan 13, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have diesel generator Kipor kde 19 STA3 . It keeps shoutinng dowen after it starts


First check the oil, A low oil sensor will shut it down if more than a quart low. Then drain your water separator and change fuel and air filters. Anything outside of that is going to be mechanical (lift pump, injection pump)

Jul 17, 2017 | Cars & Trucks

1 Answer

My Kipor KDE16STA3 shows p03 error after 15 min runing and shuts down after 3 sec.The voltage drops to 30,40 whta's happening?


[PDF]DIESEL GENERATING SET

www.kipor.com/upload/spec2011053011590766.pdf
3/KDE16STA3/ ..... P-03 Undervoltage: Indicating voltage higher (lower), the generator will self- braking. P-04 Generator ... KDE16STA3 KDE19STA KDE19STA3.

[PDF]2

www.kipor.com/upload/spec2011061109073968.pdf
P-03. Decrease load less than the related load, turn on the breaker. P-04. Replace the fuse of the same type. Check the circuit and inserter. Replace the starting ...

Oct 31, 2015 | Kipor Electrical Supplies

1 Answer

Hi, My KDE 6500T wont start, i replaced the battery and when i switch start, i can hear a tick but no ignition ,and the battery cable become tooo work


Check engine isn't locked down, rotate by hand, then check starter motor, and solenoid. The click you hear is probably the solenoid clicking in.

Feb 24, 2015 | Kipor Electrical Supplies

1 Answer

What could be the problem if KIPOR KDE 6500T Diesel generator turns off when I switch the breaker on?


is it air bound , clear it out , or you have a short but I would go with the latter ,

Dec 03, 2014 | Cars & Trucks

1 Answer

Kipor kde 6700ta GENERATOR


There is, on most generators, a fuse of approximately 8Amps in series with the charge system for the battery.
If the generator produces AC and there is no charge to the internal battery, I would suspect the altenator winding, diode pack or regulator.

Nov 14, 2013 | Computers & Internet

1 Answer

Hi, I from Indonesia and I need help... I have Kipor KDE 6700T that can starts but produce lot of smoke (white) and consume more fuel,,, Please how solve that problems


maybe your generator has a problem with the cylinder head gasket.try to remove the cylinder head gasket,grind the valves intake and exhaust it. use the gasket cement to glue the cylinder gasket then assemble it

Feb 24, 2011 | Electrical Supplies

2 Answers

KIPOR KDE 6700TA 5KVA Generator


forget about the display read the manual and find out how many volts are needed to charge the battery....then
get a voltometer and disconnect the terminals from the battery and connect them to the voltometer while the generator is running...
find out what the reading is...if the reading is zero (0)...then post a problem on (no out put)...
if not.....then there has to be a mistake...
if it reads a voltage thats too low..then you AVR card is burnt out (AVR card is located in the other end of the generator (beyond the stator-side cover)...

Aug 04, 2009 | Kitchen Appliances - Others

Not finding what you are looking for?
Electrical Supplies Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kipor Electrical Supplies Experts

jhnolson

Level 3 Expert

822 Answers

Jay Finke
Jay Finke

Level 3 Expert

1338 Answers

joe_jochoa

Level 1 Expert

22 Answers

Are you a Kipor Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...