Question about Measuring Tools & Sensors

1 Answer

When I use the fatmax to measure a distance, it gives the answer in inches. Is there anyway that I can reset/program the fatmax to give me the measurements in feet

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,123 Answers

Yes press and hold the units button for more than a second until the desired units show up

Posted on Apr 25, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the rolling offset using 45 deg bends


The formula for 45 degree bends is offset" x 1.414 equals the travel distance in inches. Example: to calculate the offset of a line 6 1/4", in other words move the line over. Turm 1/4 into decimal form (1 divided by 4=.25). Calculate: (6.25 x 1.414= 8.8375). To convert the decimal form of .8375 to a fraction multiply it by 16 (16/16=1") example: .8375 x 16=13.4 , 13 is the numerator, 16 is the denominator which gives you a fraction of 13/16". That gives you your travel distance center to center of a 6 1/4" offset= 8 13/16" travel distance. For accuracy in your measurement, you must subtract the fitting allowance (how much space the fittings take up in the measurement) from your overall travel distance. It sounds like a lot of steps, but using this formula gives you dead on accuracy in pipe fitting. If you know your travel distance and wish to find the offset, multiply x .707. Hope this helps.

Feb 12, 2015 | Plumbing

1 Answer

Error code 289 on modem


Que significa el error 289. Thanks.

Jun 19, 2014 | Stanley Fatmax, Tru - Laser, Distance...

1 Answer

Instruction manual for stanleytrulaser TLM100i


http://www.laserstreet.com/documents/TLM100_manual.pdf

Oct 06, 2011 | Stanley Tools Tlm 100 Fatmax Tru - Laser...

1 Answer

A rectangular park is 115 m by 95 m.At least how many complete rounds must a joggler make around the park to be sure he has run 5 km?


This is, of course, a trick question. The simple answer is 12, because the circumference of the park is 420m and 12 x 420m is 5040m. However, we are not told how close to the edge the runner is able to run, nor whether he (or she) rounds off the corners. If, for example, the park is bounded by a fence, the runner may have to run 1m inside the fence and will almost certainly not run completely in to each corner. Adjusting for these factors could reduce the distance run per lap to 410m or less, in which case an additional lap will be necessary. In fact, if the actual distance run is less than 416.67m per lap, then 13 laps must be run.

Jan 11, 2010 | Stanley Tools Tlm 100 Fatmax Tru - Laser...

1 Answer

How to basically operate my stanley fatmax, TLM100. The directions that came with it were for another Stanley product. Thanks,Ralph


Press the red button - (distance) you will see a red dot on the wall you are measuring - then you will hear a beep - release the button and read the display - the measurement should be displayed and accurate within a quarter inch.

Nov 16, 2008 | Stanley 100 ft. Tape Measure, FatMax

2 Answers

Big cliff height measurment?


You could do a bit of research as i can't remember the math's from my college days, but, it is possible to calculate the distance something travels by using its rate of descent against the time it takes to reach the ground, for instance, if gravity is measured at 9.81N/m per sec squared, then an object must speed up at the same rate from standstil every time unless the earths gravitational pull changed. If you then timed how long it takes to hit the ground you could do a simple calculation offsetting the rate of descent against time which would then give your distance. The calculation is - distance = speed x time, but you would need to factor in the the rate of change in the speed of the object from standstill to finish which is the bit i can't remember.

Aug 27, 2008 | Stanley 100 ft. Tape Measure, FatMax

Not finding what you are looking for?
Measuring Tools & Sensors Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Measuring Tools & Sensors Experts

Vuk B

Level 3 Expert

678 Answers

Brad Brown

Level 3 Expert

15557 Answers

Tom Chichester

Level 3 Expert

34170 Answers

Are you a Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...