Question about Maytag Neptune MAH5500B Front Load Washer

1 Answer

When the first load is cycling everything is fine.

But when you start the next loads it does not go through the spin cycle and stays at the 9 minute mark on timer.  Close come out soaking wet.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 36 Answers

It could be a bad or stuck tub displacement switch or a broken wire to the switch

Posted on Jul 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

LG Washing Machine Model : WD658 When using the function "Rinse & Spin", the timer decreases when rinsing. However, the timer decreases and stops at 9 minutes. This results the machine...


Try setting a lower spin speed. You may have a bulky load which the washer is having a difficult time getting up to the high speed spin you have selected. Also, did you know that on most LG washers, you can do just a spin without a rinse? Just turn the washer power on, then, without selecting a cycle, just push the spin speed selector to select the spin speed desired. This should set the cycle for about a 12 to 14 minutes pump and spin only. Then push start. You can spin that bulky load at the lowest spin, then try it again at the next faster spin if needed, without adding rinse water.

Mar 15, 2011 | Washing Machines

1 Answer

I have an Estae(whirlpool) washer that i have had for 9 yrs. It works fine until it get to the spin cycle. Then it stops and the water stays in the washer and will not drain. Every different wash mode...


Hi,

Problems with a washing machine not spinning or not draining are often inter related..

If you are having a problem with your top load washer then check out this tip...

Washing Machine does not Pump or Spin


If you are having problems with your front load washing machine then checkout this tip...

Front Load Washing machine not draining and or not spinning


heatman101

Dec 12, 2010 | Washing Machines

1 Answer

My neptune washer will start and run about half a cycle and it acts like it gets stuck and on one cycle and never shuts off. I put a load of clothes in before I went to bed and next morning the machine...


What does half a cycle mean are you in Wash cycle, Spin Cycle? What does the Cycle Status LED indicate?

3cbd09e.jpg

If you think the wash load is in a spin cycle of the wash cycle or rinse cycle place the machine in Spin Only cycle and see if it will complete.


Waht are your DIY skills? Do you want to try the repair/fix?.............Rich

Oct 18, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

In the Spin cycle, after 9 minuts, it will stop with a "UL".


"UL" means "Unbalanced Load" - make sure the washer isn't overloaded first or if you are doing rugs, blankets, or lots of jeans, split the load. You can also try running an empty or light load and see how the machine behaves.

If you still have the problem, you may have some issues with the drum bumpers, etc., but try the easy things first.

Jul 12, 2010 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

Wont finish a small load. Gets to 4 minutes and


With a small load, the machine will have a difficult, if not impossible job of balancing the load. A bigger load will help. Another thing you can do is to use a low spin speed. If you wish to spin it out faster, just turn the machine back on after it has finished a cycle on the low spin speed and just push the spin speed button without selecting a cycle. You can touch the spin speed button until it shows the next higher spin speed, then push the start button and the machine will not fill with any water, it will just pump and spin. (about 14 minutes) This generally works, because you have spun most of the water out at a lower spin speed, and now the washer is able to reach the next higher spin speed as the load is not as unbalanced as it was before the low speed spin.

Nov 17, 2009 | LG WM0642H Front Load

1 Answer

Will not go into high speed final spin after rince cycle..only spins back and forth slowly and the uE indicator comes on stopping the machine. Have tried taking out a few laundry items and re-starting and...


uE is unbalanced error. When you have bulky items, wash them with a slow spin speed. Larger loads actually balance out better, so adding items might help instead of subtracting them. After the cycle completes, if you want to you can turn the power on again and (without selecting a cycle) just push the spin speed selector button and select the next highest spin speed. The load will most likely make it through the next higher speed now that it is partially spun out. You should get a 14 minute spin and pump only when you start it now.

Nov 15, 2009 | LG WM0642H Front Load

1 Answer

I have an LG front loader, gets stuck on spin cycle at 9 min


The timer is likely failed.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Jul 10, 2009 | LG Washing Machines

1 Answer

Frigidaire washing machine gets stuck on cycles


The cycle doesn't advance When the cycle doesn't advance, it's probably the timer or a cold-water supply problem:

  • It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer.


  • It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. See There's no cold water.

Apr 01, 2009 | Frigidaire Washing Machines

1 Answer

14 cycle front load washer fridgidaire


press cancel. (turns off washer)
press start/pause (wake up)
hold cancel and start/pause 10sec

last error code will come up.

E47 door lock error

check wires connections to the door lock..

replace door lock..

hope it helps

Aug 08, 2008 | Frigidaire ATF6000ES Front Load Washer

2 Answers

Frigidaire top-load washer Loud noise during spin


its either the upper spin bearing or lower spin bearing. the upper can be replaced by itself but the lower requires the transmission the be replaced

Nov 20, 2007 | Frigidaire FWS833A Top Load Washer

Not finding what you are looking for?
Maytag Neptune MAH5500B Front Load Washer Logo

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

588 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

John Tripp
John Tripp

Level 3 Expert

4655 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...