Question about Klipsch Audio Players & Recorders

Open Question

Klipsch rsb-11 subwoofer pairing - it says it's paired but not getting any bass- can you help

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

trintek
  • 111 Answers

SOURCE: subwoofer wiring diagram

parallel wiring. hook all 4 positives together and run to the positive output from the amp, hook all 4 negatives together and run to the negative output from the amp.

hope this helps,
trin

Posted on Nov 19, 2007

  • 1 Answer

SOURCE: Plantronics 520 will not pair

"Begin with the headset turned off. Press and hold down the silver call control button in for 6-10 seconds. The light will flash blue first. Continue to hold the button down then release the button when the indicator light starts flashing red then blue."

Posted on Jan 06, 2009

  • 1 Answer

SOURCE: BlueAnt pairing with iphone...help

Just got off the phone with Apple and Blue Ant tech support.

If everything is workon g on both devices you probably need a memory dump on your headset.

1. Power off both devises
2. Power on iphone
3. Power on blue Ant - not in pairing mode - you should see 1 blue blinking light on MFB
4. Make sure iphone bluetooth is on and searching for devices
5. On Blue Ant, hold both volume buttons and MFB at the same time until you get a fast blinking blue light.
6. Check iphone it should now recognize device.
7. When Blue Ant shows up on phone press it so it completes the pairing priocess

Good luck!

Posted on Jul 02, 2009

  • 2 Answers

SOURCE: Won't Sync with the Subwoofer

i can't get mine to pair ... has it paired for you? thx

Posted on Jan 01, 2010

vanherringto
  • 1738 Answers

SOURCE: trying to pair blueant supertooth 11 with nokia

On most phones, you'll go to: Settings > Connectivity > Bluetooth > (turn on) > Phone visibility (shown to all / on) > Search for devices >Choose headset (when located) >
The password is 0000 (four zeros),

I don't have the link for the Super tooth II manual. but here's the link for the Supertooth One manual: (it may help)
http://www.supertooth.net/img/one/mdp_EN.pdf

You'll need Adobe reader to view it. It's free. Download here if you need it:
http://get.adobe.com/reader/

If you found this information helpful, please give me a big thumbs-up when you rate my answer. Thanks!

Posted on Feb 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a pair of linn komponent 104 speakers i was wondering if i can add a sub woofer to my amp to give the sound more bass as the speakers dont have a good bass sound


The Linn's should have a good bass, clean & tight but not boomy. Have you got them correctly phased? Red-to-red, Black-to-black? Bass is killed if one speaker is anti-phased.

Nov 11, 2014 | Car Audio & Video

1 Answer

How to replace capacitor on M Audio bx5a speaker


http://mr-ives.blogspot.nl/2011/09/mending-pair-of-m-audio-bx5a-monitors.html

Apr 20, 2013 | Klipsch Synergy Sub12 Subwoofer Speaker

1 Answer

Klipsch Lightspeaker 5.2 One speaker will no longer communicate with base.


Hello Beerisfood,We are the Canadian distributor of the LightSpeaker. Sometimes very rarely the LightSpeaker may "un-pair" and "re-pairing" the unit to the base is needed. It takes under 10 sec and is very easy to do but must be performed in a specific manner. 1. Power to the LightSpeaker must be off.2. Turn on transmitter (base) 3. Press the "pairing" button on the transmitter (base)
-lights will flash on the transmitter, during that time that they flash, turn power "on" to the LightSpeaker. The light on the LightSpeaker should now be green.
Youtube has a great video as well on pairing. Type Klipsch LightSpeaker and the first video should walk you through the process. If that does not work contact www.lightspeaker.net as they are the manufacture of this product.(Klipsch was just the US distributor not the manufacture)
Hope that helps.

Jun 02, 2012 | Klipsch Lightspeaker 5.2.0 Wireless Sound...

1 Answer

I have a Klipsch Sub-10 It is NOT working. I am not sure what happened. It was just fine last week. It's powered up and everthing but not throwing any bass. It was also detected during the auto setup.


If you're saying the auto setup produced sound then the sub and its amp are fine.

So we need to examine the source electronics for actual playback settings. Give a hint of what that might be.

Feb 19, 2011 | Klipsch Synergy Sub-10 Subwoofer Speaker

1 Answer

It is rip in to little piecies


It may not be worth the expense, but if the cone or surround are torn, they can be replaced by a speaker repair shop. I just had a pair of JL 10W6's re-edged (the foam surround around the cone deteriorated after 11 years), and the repair cost $100 for the pair, including parts.

Nov 01, 2010 | Thump TBB102 Car Subwoofer

1 Answer

I have a bose v20 and a harmon kardon receiver. Should I be returning the bose system, buy just the speakers, and and outside subwoofer, or what is the best system for watching movies etc? What would be...


If you have the harmon kardon receiver, check out this reasonably priced system. You can actually find it cheaper than at this website but I have these speakers and, when paired with the Klipsch sub-woofer, it makes movie watching an unbelievable experience.

http://www.klipsch.com/na-en/products/quintet-sl-home-theater-system-overview/

Good Luck!

Oct 19, 2009 | Bose 901 VI Main / Stereo Speaker

2 Answers

I have just been given a pair of aiwa speakers sx-fz1800,there is two cables comming out of the back,which one do i use.


One pair goes to bigger speaker (woofer) and other pair for smaller speakers in box, to get full frequency response, you need to hook both cables.

Sep 10, 2009 | Audio Players & Recorders

1 Answer

I have a pair of TDL studio 10 speakers, both bass cones on one side are dead...any suggestions?


I'm guessing that you have Bi-wireable binding posts on the back and your jumper straps are not installed. You'll be able to tell if they are biwireable if there are 4 sets of speaker connections vs the standard two. When you are only using one set of speaker wires you need to have metal straps installed between the upper and lower pair of connections so that all of the drivers are getting signal.

Jun 06, 2009 | Audio Players & Recorders

2 Answers

Klipsch ksw subwoofer wont power on


The power supply switching transistors are likely fried. Dangerous high voltages involved. I would remove the plate and send it to Klipsch for repair.

Jan 16, 2009 | Gem Sound SUB-650M Speaker

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Klipsch Audio Players & Recorders Experts

The Knight
The Knight

Level 3 Expert

73619 Answers

rhodesworks

Level 3 Expert

3082 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

1773 Answers

Are you a Klipsch Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...