Question about Office Equipment & Supplies

Open Question

Service mode workcentre 5222 - Office Equipment & Supplies

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
goodgold
  • 389 Answers

SOURCE: XEROX WORKCENTRE 5222/5225/5230 A FAULT OR

010-150, 155 Too much or not enough paper in duplex tray 10-300 Fuser thermistor 10-302 Low fuser temperature 010-304 Bad fuser temp 10-308 High fuser temperature or open thermistor 010-310 High fuser temperature 010-312 Fuser not up to temperature after energy save 010-314 Fuser problem 010-320 Fuser web finished 010-330,327 335, 340 Exit switch, vertical sensor switch actuated when power is turned on

Posted on Sep 13, 2009

Ad
  • 2072 Answers

SOURCE: error code 010-320 for workcentre 5222

That is a fuser heat roll over temperature.
You will need to replace the fuser module .

Posted on Feb 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error code 062-277 I need to solve the error how can do it


https://printcopy.info/?l=en&mod=erc&brand=Xerox&model=WorkCentre%205021&code=062-277


Xerox WorkCentre 5021 Error Codes


Code

062-277

Description

DADF Communication Fail Transmission cannot be established between the ESS/MCU PWB and the DADF PWB.

Remedy

1. Turn the power OFF and ON. 2. Turn OFF the power and check the connections between the ESS/MCU PWB J421 and the DADF PWB J751, J752 for open circuits, short circuits, and poor contacts. 3. If no problem is found, replace the following parts in sequence: • DADF PWB (PL 56.2) • ESS/MCU PWB (PL 18.1)

Jul 04, 2017 | Xerox Office Equipment & Supplies

1 Answer

Error 010327 in xerox work centre 5222


That error signifies a defective fuser unit. Replace fuser, part number 126K24980.

http://www.iteminconline.com/126k24980_126k24980-126k24981-126k24982-126k24983-126k24984-xerox-workcentre-5225-5230-fuser-110v-new.htm

Feb 22, 2016 | Xerox Office Equipment & Supplies

2 Answers

Xerox WorkCentre M128 hard reset


Yes! what you will need to do is...

Hold down the [0] for 7 seconds and press [start] without releasing the [0]
you will be prompted for a password. enter [6789] and press confirm
select system settings followed by administrator log in/set up and change the password back to [11111]

hope this helps!

If you need further help, reach me via phone at https://www.6ya.com/expert/brandon_df19fc5eb3312a55

Jul 04, 2012 | Xerox WorkCentre M128 Copier

1 Answer

Error code 010-320 for workcentre 5222


That is a fuser heat roll over temperature.
You will need to replace the fuser module .

Feb 16, 2010 | Xerox Office Equipment & Supplies

2 Answers

XEROX WORKCENTRE 5222/5225/5230 A FAULT OR ERROR FAULT CODE 010-327


010-150, 155 Too much or not enough paper in duplex tray 10-300 Fuser thermistor 10-302 Low fuser temperature 010-304 Bad fuser temp 10-308 High fuser temperature or open thermistor 010-310 High fuser temperature 010-312 Fuser not up to temperature after energy save 010-314 Fuser problem 010-320 Fuser web finished 010-330,327 335, 340 Exit switch, vertical sensor switch actuated when power is turned on

Sep 03, 2009 | Office Equipment & Supplies

1 Answer

I need to restore NVRAM from the WorkCentre 2424.


1. From the System Setup menu, go to Information --> Troubleshooting --> Service Tools menu.
2. With the cursor at the top of the Service Tools menu, press both the Up Arrow and Down Arrow buttons to display the Hidden Service menu.
3. Reset NVRAM is in there

If that doesnt work try below.
1. Turn the system power ON.
2. Wait for the Xerox logo to begin moving across the display.
3. Before the logo is centered on the display (stops moving), press and hold the Back and Info buttons on the control panel.
4. Hold both buttons until the display reads 'Beginning Service Mode Initialization'. Release the buttons and the system reboots into service mode with the Service Diagnostics menu displayed. You should find it in the function sub menu.

Jul 16, 2009 | Xerox WorkCentre C2424DN All-In-One Laser...

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

k24674

Level 3 Expert

8073 Answers

jasbo
jasbo

Level 3 Expert

2237 Answers

yadayada
yadayada

Level 3 Expert

80668 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...