Question about Tools & Hardware - Others

1 Answer

Is there a manual for the Tooltec 1020w electric router no 11500-32000RPM

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Tools & Hard... Master
  • 45,102 Answers

Try Googling (tooltec)(1020W)(manual) without parens.

Posted on Apr 20, 2017


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where to put batteries for laser on a tooltec 1800w mitre saw part no.273102 ?

I am not at all familair with your particular saw, but I have seen and used many other miter saws with lasers, so I hope this will help:

Many saws install the whole laser assembly right at the center of the saw blade itself. If you look, very likely you will see two pretty beefy washers, one on either side of the blade, right where the motor's arbor passes through the center hole of the blade. One of these washers is the laser itself. complete with batteries. Please unplug the power and take a close look; I'll bet you will be able to spot the lens of the laser.

If your laser turns on automatically when you spin the blade, this is almost certainly where the laser is. In the beefy washer is the light source, a couple of button batteries, and a centrifugal switch that closes when the balde sipns fast enough, thereby turning on the laser. When you release the trigger, the saw slows and stops, the switch is no long held closed by centrifugal force, and the light goes out. Pretty slick!

To replace the batteries, unplug the power and remove the blade according the instructions in your manual. Be aware that many saw blade arbors and their retaining nuts are LEFT HAND THREADED.

Look closely at the washer to see how it comes apart, and take the batteries with you when you shop for repalcements.

If you don't have the manual, speak up, and together we go over blade removal/blade changing, but it is pretty straightforward. Good luck.

Nov 14, 2017 | Saws

1 Answer

Tooltec 1800w mitre saw all I did was change the blade and now the saw is dead

Does the motor hum when you pull the trigger? If so, check that the push tab for securing the shaft from turning while changing the blade is pulled out all the way. Sometimes fine saw dust can get inside and prevent the spring from pushing the tab back out all the way. If there is no hum, check the power source.

Mar 23, 2017 | Blade Saws

1 Answer

Tooltec mitre saw /table saw owners manual

Where did you buy it? What result did you get at your local tool dealer? Is it badged as something else because I can't find a dealer or importer?

Feb 23, 2015 | Saws

1 Answer


That part may not be available anymore.

I would call Encompass toll-free at 866-779-5835.

Good luck.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

Sep 25, 2009 | Goldstar MA-1020 850 Watts Microwave Oven

1 Answer

Apex 1020W dvd tray will not open

Well after taking the cover off, i "toyed" with the tray (pushed down on the round white part then let up, after first pressing the open button on the unit) the tray opened almost all the way wouldn't close so i closed it repeated the same "trick" the tray opened all the way as it should. just have to close the tray my self by hand.

it played a (Brand new dvd from Wall-mart, that will not play with out stoping in the "old" machine at the house) but stoped in about the same places, but recovered more quickly after playing another DVD i replaced the cover it works

Thank you for the help

Jun 05, 2009 | Televison & Video

1 Answer

Zanussi zwf 1020w drum not revolving

The drum will not rotate until the draining process is satisfied, there is either something in the pump or pump is broken

Oct 20, 2008 | Zanussi FJD1666W Front Load Washer

Not finding what you are looking for?
Tools & Hardware - Others Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tools & Hardware - Others Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Brad Brown

Level 3 Expert

17326 Answers

john h

Level 3 Expert

15360 Answers

Are you a Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides