Question about Frigidaire Dryers
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
ngfam1 here for you!
I am happy to be of assistance!
Did you check the owners manual first to see about the blinking codes?
Usually the codes mean you just have to have factory service remedy the problem!!!!!!!!!!!!!!!
This is a situation that you will need service!
If this dryer is 10 years old or more do not spend any money on it!
The new ones are much more efficient! If you have to replace it buy a Speed Queen , it will do 8 loads a week for 25 years!
It's the last washer and dryer I will ever buy!!!! And less expensive than a top of the line unit!
Here is the service company I refer my appliance customers too!
A&E Factory Service
A Nation Wide Company. / Available 24 / 7 for arranging appointments! In the USA.
You will be fine now!
PS. PLEASE GIVE ME A GOOD RATING HERE ON FIXYA.COM BEFORE YOU SIGN OFF!
Posted on Aug 28, 2008
SOURCE: I have a Frigidaire gallery
the dryer circuit will be clearly labelled in the house box, there will be two fuses or a single two phase breaker for this circuit.
there are not usually electrical fuses as such IN a dryer, there are thermostats to regulate temperature, and a thermal fuse, that cuts the power totally to the heat element if air temperature rises above its melt point.
the element itself has a limited life span and may fuse/burnout.
to test electrical components.
open case, by removing the front,
described elsewhere in any of the 'changing belt' threads
locate the thermal cutouts, on the fan housing or exhaust duct and disconnect one wire to isolate it from the rest of the circuit, test with ohmmmeter, no-continuity replace, continuity reconnect wire
thermal cuttouts look like these ~1inch accross.
locate the heat element and disconnect one wire to isolate it from the rest of the circuit, test with ohmmmeter, no-continuity replace, continuity reconnect wire
while you have the dryer open de-lint the fan and exhaust ducting, most common cause of element or themal fuse failure is air flow restriction
you get a lot of lint out of the fan even when proper cleaning is done, and clean out the ducting right to the exterior walls
this was the rather extreme result of not cleaning the duct (brainiac placed a wire across the terminals of the burnt out thermal fuse)
Posted on Oct 23, 2008
When ours does that it is because of the hard water build up. We have to un-hook the hot water clean out the minerals and it stops doing it.
Posted on Dec 03, 2009
The thermistor or control thermistor is located on the blower housing at the right side of the dryer base. It can only be accessed when the front panel is removed. Disconnect power and remove the top panel then the control panel to expose the screws securing the front panel to the cabinet. Once the securing screws are off, disconnect the wire harnesses going to the front panel then lean the panel forward and lift it off the bottom clips.
Posted on Jan 29, 2011
Testimonial: "Thank you, your solution is perfect for what I needed unfortunately I was desperate and did not think I would get this solution to my problem so quick"
Tips for a great answer:
Jan 03, 2016 | Frigidaire FGET2765KF
Thank you for your inquiry, friend!
I understand that your Frigidaire dryer has been providing you with an error code "PF". Typically "PF" stands for power failure this can happen if power is shut off during a cycle or the dryer receives insufficient power, which could be an issue with your power cord or control panel. Let's perform a reset on your dryer and you can do this by unplugging the power cord for ten minutes. If you need any additional assistance please feel free to reconnect. -Matt
Oct 14, 2014 | Dryers
Jul 17, 2014 | Frigidaire Dryers
Jun 27, 2014 | Frigidaire Dryers
Mar 05, 2012 | Frigidaire Dryers
Jan 29, 2011 | Frigidaire Dryers
Here is a tips that I wrote that will help to explain why you get the PF Error Code
PF Error Code for Appliances
Jun 27, 2010 | Frigidaire GLEQ2152ES Electric Dryer
Oct 07, 2009 | Frigidaire GLTF2940E Gallery 3.5 Cu. Ft....
Jul 30, 2017 | Frigidaire Dryers
37 people viewed this question
Usually answered in minutes!