Question about Microtek Computers & Internet

1 Answer

How do you adjust the voltage on a 600 ups Microtek inverter ?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 923 Answers

Adjust what voltage? Input range? Output range? Need a lot more info, for a useful response!

Posted on Apr 18, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Microtek Inverter high output problem


Did you check the voltage under load, some power supplies float high when there is no load connected

Mar 01, 2014 | Electronics - Others

1 Answer

I have 800va microtek inverter non sine wave.i want to know what is the output voltage available


The voltage should be the same for both. Maybe one or the other isn't calibrated correctly. Have a friend with another multimeter check the output, and then take the voltage that is the same from his and yours.

Sep 19, 2012 | Office Equipment & Supplies

2 Answers

Hi, I have Microtek 810 Inverter, it is charging properly, problem starts when mains goes off and inverter is in Battery mode, then output of inverter shows no voltage, even i conected multimeter to...


Good day!

You have to do is:
Check the battery if it is leak.Use a voltmeter to test the output voltage of the battery.If your battery had a low supply voltage even you charge it for 3 hours and above.Replace the battery immediately.


Thank you and good luck.

Apr 21, 2011 | Vacuums

1 Answer

I am using microtek 810. Inverter section is ok. In the pcb there are two 40amp fuse which were blown off. suspected heavy current drainage. both fuses are in parallel and in the battery -ve line. i...


If this is a 12 volt battery situation, 24.6 volts is not doing good things for your batteries--it will buckle the inner plates causing immediate battery failure. Were the fuses themselves blown or just the fuse mounts which may have been underrated. You definitely need a schematic for this system--try googling 'microtek 810'. Good luck!

Aug 15, 2010 | Garden

2 Answers

MICROTEK INVERTER HELP


Bad batteries, replace all of them together.

Oct 02, 2009 | Electronics - Others

2 Answers

Battery back up supply


it is possible that the fuse for the input of power is broken or bad

Feb 11, 2009 | Energizer ER-HM650 UPS System

1 Answer

Microtek Inverter not fully charging the batteries


xenion pure shinewave inverter not charging fully

Jan 17, 2009 | Computers & Internet

3 Answers

Monitor makes popping noise when power is on.


Sounds like an inverter problem. If the power supply is internal replace the capacitors coming out of the voltage regulators. These are usually 1000mf and/or 470mf. If that doesn't do the trick look up the numbers on the 8-pin chips that drive the secondary transformers on the inverter to see if they are getting the right voltages.
Good Luck!

Feb 19, 2008 | Microtek 211SD 21" LCD Monitor

1 Answer

Error 600


I bought the pro version of the 8700, used it about once a month--very light use. When it died, I found that Microtek won't even sell parts! I agree, NEVER buy another Microtek product! This thing cost me over a $1000 and after one year, NO support! Any company but Microtek.

Dec 06, 2007 | Microtek ScanMaker 8700 Flatbed Scanner

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Microtek Computers & Internet Experts

William Miller
William Miller

Level 3 Expert

9047 Answers

John Anderson
John Anderson

Level 2 Expert

310 Answers

solver2010

Level 3 Expert

923 Answers

Are you a Microtek Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...