Question about Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

1 Answer

Stopped near end of cycle, water in bottom and no lights will come on when pressed

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 296 Answers

Hi
seems there is probably water in the drip pan below that needs to be emptied or evaporated out. but if there is water ther is an internal leak such as a bad hose or door seal thats need to b fixed.
unplug the unit or open up the bottom behind the toe kick and **** out all the water and find the leak by running it with the cover off till you see it.
hope it will work for u
all the best
,for further queary ,plzz do let us kno.
regards

Posted on Jul 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Machine will not finish any wash cycle, It stops, illuminates END light and beeps? Is there a reset or is this at the end of it's life?


Hi, quite often cycles are not finished because the drain pump has an intermittent fault. It may pump ok at the start of the cycle but towards the end it's had enough and stops. Leaving water in the bottom of the drum. If this is similar to your machine's symptom then I would be checking the pump. They are cheap to buy and easy to fit.
Hope this helps you.

Oct 04, 2015 | Washing Machines

1 Answer

Dishwashwer continues a motor noise long after the quick rinse cycle ends


Hello Deborah!

Well, don't use the quick rinse cycle!

All seriousness aside, dishwashers are supposed to stop on the pump out cycle when the water level switch trips, indicating the tub is nearly empty (a little water always remains to protect the seal).

Why your problem exists only on quick rinse is a mystery, but I would check the water level float mechanism. They have a way of accumulating grunge and sticking. While many float switches are easily accessible in the front, bottom corner of the tub (and "click" as they are raised and lowered), some live in a container on the outside of the tub and may only be checked by pulling the whole dishwasher out.

All the best.

Nov 22, 2014 | Kenmore Dishwashers

1 Answer

Dishwasher wont completely drain and turns off


Good Morning Friend,

I understand that your Frigidaire dishwasher shuts off near the end of the cycle, leaving water in the bottom of the tub. I also see that the display is going black. I suggest resetting your appliance, by either unplugging it or shutting the power off at your homes circuit breaker, for 20-30 minutes. When power is restored, run any cycle. If you are still noticing your dishwasher shutting off towards then end of the cycle and water being left in the tub, I suggest contacting your local authorized technician for further assistance. They will be able to diagnose your appliance and determine what is causing it to shut off and not drain. Hope this is helpful.

-Best regards-
WP

May 14, 2014 | Frigidaire Dishwashers

1 Answer

Kenmore Dishwasher has died part way through a wash cycle.


The control module has failed, you can check for broken solder joint s or obvious damage but it's hard to diagnose the exact cause remotely.

Mar 12, 2012 | Dishwashers

1 Answer

F27 came up nearing the end of the spin cycle and just stops after it's spun but doesn't finish and release.


Close the washer and press the START/PAUSE/Cancelbutton to remove error displayed and restart the cycle. If it doesn't work, it means thatthe valve at the water entry needs to be replaced..

Hope this helps..

Jun 10, 2011 | Siemens Washing Machines

2 Answers

What is E25 on my Bosch super silence dishwasher?


I quote same wrong from other user:

Question: Model dishwasher is Bosch Exxcell SMS50E02
It stopped before the end of a cycle with the error code E:25 and the "check water" light came on
I mopped out all the residual water out of the bottom and then ran a rinse cycle, which after several trials I got to work and then it stopped at the end again with the same error code and water in the bottom as before.

Answer:
I assume by in the bottom you mean inside the dishwasher and not in the base.As long as there is no debris in the sump area and the hoses are clear it appears you have a bad drain pump.

Hope helps.

Apr 03, 2011 | Dishwashers

1 Answer

Condensation in dishwasher


Make sure you aren't selecting the eco setting to conserve power. Running a dishwasher in that mode disables the heating element that dries the dishes at the end of a cycle. Here a few ideas you can try,... with an empty dishwasher.. start a cycle and make sure you do not use that ECO mode if it has that feature.. then stop the dishwasher when it near the end of the cycle and open the door ./.. check to see if the water has been drained and that the heater element is on and hot. If there is a high volume of water in the bottom of the dishwasher, make sure the darin filter screen is clean and not restricting water flow... If that is clean.. and you have a lot of water in the bottom pan, you could have a problem with the pump, a hose in line with the pump or your house drain system is restrictive.. Good luck... and Hope this helps you..

Nov 29, 2009 | Kenmore Dishwashers

1 Answer

The dishwasher has been running for 3 hours and seems to be stuck on 1 minute left. Upon opening, there was sudsy water remaining in the bottom, but the dishes looked clean. The washer just won't go to...


SHU 53 MODELS To start test program, press and hold both SCRUB WASH and DELICATE/ECONO program buttons, then turn unit on by pressing ON/OFF button. Initially, control module version # will be displayed (e.g./ ?21? = version 1 with jumper). When wash program buttons are released, lights above them will flash. To end test program, press ON/OFF button. To check each program indicator light, press its button. To check Cycle Countdown display, Refill Rinse Agent light and REGULAR WASH light, press REGULAR WASH button (press Delay Start button to test Cycle Countdown display alone). Cycle Countdown display will show ?88″ when REGULAR WASH button is pressed and ?8h? when Delay Start button is pressed. To start testing, press both the SCRUB WASH and DELICATE/ECONO buttons a second time. When testing has ended, Cycle Countdown display will show a fault using codes below. If more than one fault occurs, code numbers will be added together, (e.g./ ?6? = faults 2 + 4). 0 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault 1 = Aqua Sensor (?Sensotronic?) fault 4 = Filling fault F = Filling fault (display occurs during wash, not test) To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil, measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays at ~ 1.5-2 A, then heater, high limit or flow switch are faulty. If water level switch (f1) has failed (opened), display will show fault code ?4″ and unit will continually fill and drain where testing won?t be completed. If flow switch (e5) has failed (opened), display will show ?0″, water won?t heat (to 150?F) and water won?t stop circulating. If NTC probe (f2/f4) has failed (opened), display will show fault code ?8″ immediately and testing will end shortly after water has started circulating.

Aug 01, 2009 | Bosch SHU5315UC Dishwasher

1 Answer

LG Dishwasher Model LD-1403W gets stuck and stops on rinse cycle leaving water in bottom of machine. I have stripped it down and emptied it, made sure filters etc are clean but to no avail


LG Dishwasher LD 1403W. We have cleaned it and when it gets to the heating cycle after running right through to nearly the end, it trips all the electricity and stops everything. Its only 3 years old and hubby thinks its the heating element but between $200=$300 to fix.

Apr 10, 2008 | Dishwashers

Not finding what you are looking for?
Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher Logo

Related Topics:

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dishwashers Experts

Ken Johnston
Ken Johnston

Level 1 Expert

56 Answers

Fred Sops

Level 2 Expert

272 Answers

D. E. Hev

Level 3 Expert

1167 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...