Question about Dacor Preference RSD30 Gas Kitchen Range

1 Answer

Oven Failure Code F1

About an hour after cooking with the oven the F1 code lit and beeped. If I cut the power to the unit at the circuit breaker, the code clears and the oven operates normally for cooking. When the oven is turned off (pushing the "cancel" button) the F1 failure again occurs during cool-down.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 725 Answers
Re: Oven Failure Code F1

F1 is a Relay circuit failure . you have a bad relay PCB or wire connection.

to fix your F1 error
92028 RELAY PCB, 105 C

Posted on Aug 25, 2008

1 Suggested Answer

  • 154 Answers

SOURCE: Oven Failure Code F1

sir what type of oven u r using???

Posted on May 26, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

F1 came on when i was cooking with my oven and stove top on

Here is some wisdom for understanding F1 fault codes.

In some models, there are subcodes that make diagnosis even easier.

Here's a simple explanation of what's going on and how to troubleshoot:

The F1 code indicates that:

a. The electronic range control (ERC) is sensing heat in the oven when in a time-of-day (i.e., not cooking) mode.

b. The ERC is receiving information to run multiple heat functions simultaneously.

Although different components (depending upon the model) could generate the code, simple and straightforward testing using your ohm meter is all you gotta do to test for it.

1. Check the oven temperature sensor. The oven sensor has to be within spec or it will cause the F1 code.
As an example of being out-of-spec, the ERC will generate an F1 fault code when the sensor shows 1650 ohms during a time-of-day mode.
This is equivalent to 350°F in the oven.
The resistance isn't high enough to generate an F2 code (runaway temp) or an F3 or F4 code (shorted/open sensor circuit).
The ERC monitors the sensor circuit after a heat cycle and expects the resistance to drop back to 1050-1100 ohms.
The fault code is generated when this doesn't happen. Checking the sensor circuit means also checking the harness,
harness connections and the sensor itself.

2. If the oven sensor circuit checks okay, then turn your inquisitive eyeballs to the touchpad.
If the range has a separate touchpad/keyboard, the keypad may have moisture that is shorting several circuits simultaneously.
If the F1 code is given immediately (instead of during or after a heat cycle),
remove the ribbon connector from the touchpad to the ERC after clearing the F1 code. If the F1 code does not return in five minutes,
then cast a suspicious gaze upon the touchpad/keyboard. Shorts may be caused by using an ammonia-based glass cleaner.
The touchpad surface will absorb ammonia-based cleaners that are sprayed directly on the glass surface. When heat is applied,
the surface material can break down causing shorts.
If you're gonna use ammonia-based cleaners on your control panel, then you should spray it on the rag and then wipe the touchpanel
-don't spray directly onto the surface of the touchpad.

3. On Amana ranges with a rotary temperature dial, be sure that the knob is in the OFF position when performing tests.

4. If these tests all check good, then replace the ERC.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

May 25, 2010 | Kenmore 94312 / 94314 Electric Kitchen...

2 Answers

Oven Failure Code F1

sir what type of oven u r using???

May 26, 2008 | Dacor Preference RSD30 Gas Kitchen Range


Troubleshooting KitchenAid oven, range and microwave error codes

Here list of Kitchen Aid range and oven codes.
4 Digit Failure Codes
F1 - E0 EEPROM communication error
F1 - E1 EEPROM checksum error
F1 - E2 UL A/D error
F1 - E4 Model ID error
F1 - E5 Calibration shifted
F1 - E6 Latch signal mismatch error
F1 - E9 Stack overflow
F1 - E3 Wiring harness cavity size does not match stored value
F2 - E0 Shorted touch pad
F2 - E1 Keypad cable connection error
F2 - E5 Cancel key drive line open
F2 - E6 Cancel key drive line open
F3 - E0 Oven temperature sensor (RTD) opened (upper oven on double oven models)
F3 - E1 Oven temperature sensor (RTD) shorted (upper oven on double oven models)
F3 - E2 Oven temperature is too high (Cook mode)
F3 - E3 Oven temperature is too high (Clean mode)
F3 - E4 Oven temperature sensor (RTD) opened (lower oven on double oven models)
F3 - E5 Oven temperature sensor (RTD) shorted (lower oven on double oven models)
F3 - E6 Drawer sensor open
F3 - E7 Warming drawer sensor shorted
F4 - E1 Meat probe malfunction - shorted
F5 - E0 Door Switch
F5 - E1 Self clean latch will not lock
F5 - E2 Latch during CLEAN error
F5 - E5 Self clean temperature not reached within 45 minutes.
F5 - E6 Door is open, but latch is locked
F5 - E7 Self clean latch will not unlock
F6 - E0 Return line not connected
F7 - E1 Common switch wire defective
Two digit codes:
F0 ERC Board failure
F1 ERC Board failure
F2 Oven temperature is too high
F3 Oven temperature sensor open
F4 Oven temperature sensor shorted
F5 ERC Board failure
F7 Function key stuck on ERC
F8 ERC Board failure
F9 Oven door lock failure
Microwave and Microwave combo error codes:
F1 - E3 or F1 - E4 Electronic control malfunction
F2 - E0 or F2 - E1 Keypad connection error
F2 - E3 Keypad held down too long, or keypad is shorted.
If you get an error code, try first resetting the code:
1. Disconnect power for about two minutes.
2. Connect back power.
3. If code re-appears, test and eventually replace faulty part.

on Apr 24, 2015 | Kitchen Ranges

1 Answer

Jenn-Air SCE 30600, oven error codes F1 and Probe

An F-1 error code on your model means the element was energized when it should not have been, A shorted interconnect harness or failed power relay board.

A probe indication could be a failed meat probe jack or bad harness in a unit that has one. In a unit without a meat probe, suspect a bad board.

Both conditions would warrant bringing in a tech.

Before you do, turn off the circuit breaker fot 3 miutes and turn it back on. This will reboot the boards. If problem persists, the call a service tech.

Nov 04, 2009 | Jenn-Air SCE30600 Slide-In Electric...

1 Answer

F1 service code

The owner's manaual states that F1 means Control Malfunction.
The manual recommends the following:
Press Oven cancel pad or disconnecting power supply may eliminate F code. If failure continues contact an authorised dealer.

Aug 02, 2008 | Amana ACF3325AS Dual Fuel (Electric and...

5 Answers

Maytag Gemini Electric stove fault code F 1-2 when using the oven(s)

F1-2 Runaway Cook Lower Oven Check the sensor 1050-1100
ohms, wiring, control

F1-8 Keypad Shorted Replace Control

Here is the link for you to print off the service manual on your range

PLZ Rate my service

Feb 17, 2008 | Maytag MER6772 Gemini Electric Kitchen...

1 Answer

F1-6 Fault Code

This code is in responce to a fault/failure in the lower keypad assembly. It is possible the keypad was bumped.

Maytag Gemini fault codes.
Fault code Suspect area Fault code Suspect area
F0 - 0 None
F1 - 1 Runaway cook upper oven
F1 - 2 Runaway cook lower oven
F1 - 3 Runaway clean upper oven
F1 - 4 Runaway clean lower oven
F1 - 5 Keypad cancel upper
F1 - 6 Keypad cancel lower
F1 - 7 Keypad disconnected
F1 - 8 Keypad shorted
F1 - 9 Slave

Dec 29, 2007 | Maytag MER6769 Gemini Electric Kitchen...

2 Answers

Have a magic chef oven, f1 display after self cleaning, stove top works fine, any thoughts

F-1 is a fault code.

Disconnect the power plug or turn range power off at circuit breaker. Wait a couple of minutes, then plug the range in or flip the range circuit breaker to ON.

Oven control beeps & displays any F  code error (for example 
F11) - Electronic control has detected a fault condition. Press 
CLEAR/OFF to clear the display & stop beeping. Reprogram 
oven. If fault recurs, record fault number. Press CLEAR/OFF
contact an authorized service agent. 

Dec 01, 2007 | Magic Chef CER3725AA Electric Kitchen...

1 Answer

F1 error code, continual beeping all other oven functions work properly

Here are the error codes for Dacor:

Range/Stove/Oven Fault Codes Failure
Condition Check/Repair F0 Clock pushbutton is stuck in a depressed position Check clock buttons F1 Element relay circuit failure Control board may be bad F2 Oven temperature exceeded the clean runaway temperature (self clean only) or the cooking runaway temperature (cooking modes only) Call for service F3 Short Circuit in the oven temperature sensor Check oven temperature sensor for continuity, if no resistance (zero ohms), replace F4 Short Circuit in the oven temperature sensor Check oven temperature sensor for continuity, if no resistance (zero ohms), replace F6 Failure in the EEPROM check comparison (only time of day and timer will operate) Call for service, electronic clock control is usually the cause of the problem F7 Failure of the self- clean automatic door latch system Check door latch and switch(es) F8 Failure of the door latch motor. Occurs when the motor runs for two minutes without the door locking in self-clean mode Check door lock motor and door latch

Nov 08, 2007 | Dacor Epicure ERD30 Dual Fuel (Electric...

Not finding what you are looking for?
Dacor Preference RSD30 Gas Kitchen Range Logo

1,439 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dacor Kitchen Ranges Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

Are you a Dacor Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides