Did anyone can tell me how to enter Electrolux washer Model: EWF1114UW0 service diagnostics mode ?

Please follow these procedures to activate the diagnostic mode on an Electrolux EWMGD70JPP0 dryer:

Ensure that the dryer is unplugged from the power source and turned off.

The "CANCEL" and "START" buttons should be pressed and held simultaneously.

Reconnect the dryer's power while continuing to hold down the "CANCEL" and "START" buttons.

Holding the "CANCEL" and "START" buttons together will start the diagnostic test.
That should only take a few seconds.

Once the diagnostic test has begun, let go of the "CANCEL" and "START" buttons.

Now that you should be in diagnostic mode, you can go through the various tests using the display.
The "CYCLE SELECT" knob and the "OPTIONS" button should be used to cycle through the tests, respectively.
The diagnostic mode should only be used by those who are qualified to work on appliances, as it is designed for service technicians.
It is advised that you get in touch with a reputable appliance repair provider if you are unfamiliar with the diagnostic mode or are unclear on how to proceed.

Sounds like you did great job of following the service manual and advice for parts suppliers, but often, it is service tech knowledge that is useful. For instance they will look at a board and say "yes, this board fits most of them, but not yours", or they say "these boards are made on Taiwan for 5 bucks each and 8/10 don't work, I keep 20 in the van". also these days, techs carry a laptop computer and connect to a Service Port, like the OBD2 port on a car. The machine tells them the issue.

Your choice, Service Call or Shiny New Machine. You can't do any more than you have done.

you have obviously seen this, but did you check the connection to the Inverter board on the motor and the soldered joints behind the connection? Different model, same code.

E9F: Communication Error Between Main Board And Inverter ...

https://www.manualslib.com > ... > Service manual
Electrolux EWM25 series Manual Online: E9F: Communication Error Between Main Board And Inverter Board. E9F Checks to perform: Measure the continuity between ...

Washer dryer displays error message E30, C3 or emits 3 beeps

https://www.electrolux.co.uk > support-articles > laundry
Sept 18, 2019 - Washer dryer displays error message E30, C3 or emits 3 beeps. The error is caused by water at the bottom or inside the machine.
Missing: efme517stt0 ‎' Must include: efme517stt0

Electrolux/Frigidaire combo beeps 3 times randomly ...

https://www.ifixit.com > Answers > View > Electrolux-F...
Oct 9, 2020 - Just curious if anyone would know why my Frigidaire stackable Washer/Dryer model FFLE3911Qw0 Beeps 3 times randomly and it does it all the ...

2 answers · 2 votes: Hi, Does this occur when the washer is in use? Don't know the answer but according to the ...
When I hit start Button, the dryer just beeps - Kenmore ...
7 answers
Nov 23, 2016
Why will my dryer turn on but won't start? - iFixit
3 answers
Sept 3, 2015
Frigidaire washer beeps through out cycle
2 answers
Mar 23, 2021
More results from www.ifixit.com

Try turning off the power and the lock should release.

What does e11 mean on Electrolux washer? - AskingLot.com

https://askinglot.com > what-does-e11-mean-on-electrol...
Mar. 26, 2021 - This E11 error means that the washer didn't fill up with water ... the display simultaneously for 3 seconds to enter the diagnostic mode.


..

If you cannot move the drum by hand you will not be able to fix the problem yourself by playing with the diagnostics.

A locked drum is also one symptom of a seized electric motor.

Washer topload diagnostic mode. - YouTube

? 5:00
https://www.youtube.com/watch?v=jipYd_qeCqs
Jun 17, 2014 - Uploaded by Al Fixit
How to put kenmore washer into diagnostic mode. ... How to Use HE Top Load Washing Machine: Informational Tips From Sears Home ...

Entering Diagnostic Mode in a Whirlpool Vertical Modular ...

? 1:02
https://www.youtube.com/watch?v=7kWrIPaWLUM
May 8, 2012 - Uploaded by SamuraiRepairman
Shows how to enter diagnostic mode in the Whirlpool VMwasher. Created on May ... The first was no error codes. the second said that we had an unbalanced load. I'm not sure ... I had a repair person out to my house he reset the computer panel and it worked. Now its ... washer. Raise the top panel to get it.

Diagnostic mode for Kenmore Elite Oasis HE Top Load ...

Electrolux Diagnostic Mode
* Press the Cancel button to enter standby mode and enable diagnostic entry.
* Within 10 seconds after pressing Cancel , press any button to wake up the control.
* Within 5 seconds of wake up, turn the selector knob to the far left cycle and press and hold Cancel and far left
button under the display simultaneously for 3 seconds to enter the diagnostic mode.




To save time at wake up, the Welcome screen can be bypassed by turning the selector knob.





1. Upon entering diagnostic mode, all lights should flash for 1¼"x2" display models and all lights on for the 1¼" x
4 3/4" display models.
2. Turn the program knob (1) click clockwise from the start position. The hot water solenoid will activate and hot water
should enter through the detergent compartment.
3. Turn the program knob (2) clicks from the start position. The bleach water solenoid will activate and cold water
should enter through the bleach compartment.
4. Turn the program knob (3) clicks from the start position. The bleach and the wash water solenoids will activate and
cold water should enter through the softener compartment.
5. Turn the program knob (4) clicks from the start position. The prewash solenoid will activate and cold water should
enter through the prewash compartment.
6. Turn the program knob (5) clicks from the start position. The door lock solenoid will deactivate and the loading door
can be opened. When the door is opened, the drum light should turn on.
7. Turn the program knob (6) clicks from the start position. The door lock will activate and the washer will fill then
tumble. Once tumbling has started, the boost heater will turn on.
8. Turn the program knob (7) clicks from the start position. The drain pump will activate draining out any water in the
tub and the washer will operate in high spin.
9. Turn the program knob (8) clicks from the start position. This is a free position.
10. Turn the program knob (9) clicks from the start position. The control will signal the last 5 error codes with E00
being no error.
11. Turn the program knob (10) clicks from the start position. Latest software version will be shown.
12. If applicable, turn the program knob (11) clicks from the start position. This is a free position




Exiting Diagnostic ModeA) Unplug the power cord, wait 5-8 seconds, then reconnect the power cord or
Turn the program knob clockwise back to the start position. Press the Cancel and far left button under the display

until the LED's stop flashing

Remove the top and you should find a tech sheet.

look for tech sheet. this will tell you how to enter machine into service mode. Its located either behind bottom kick panel. or under top panel.

I'll email you a few pages out of a service manual for a WPGT9360 (closest I could find to your model number) hope this helps.