Question about Cisco PIX Firewall 506E

1 Answer

Cisco pix 506e power is on but wont start

I connect on HT and i get nothing no promp but when i switch it off and then on it gives me this....

PCI Device Table.
Bus Dev Func VendID DevID Class Irq
00 00 00 8086 7192 Host Bridge
00 07 00 8086 7110 ISA Bridge
00 07 01 8086 7111 IDE Controller
00 07 02 8086 7112 Serial Bus 9
00 07 03 8086 7113 PCI Bridge
00 0D 00 8086 1209 Ethernet 11
00 0E 00 8086 1209 Ethernet 10

and thats it... it stays there

Posted by on

  • georgei Jul 21, 2009

    ok never miknd i found the solution and its working now all i did was opened the pix (took 2 screwes off) and moved the jumper in the center of the board and closed it back up and powered on the thing and it started up normally... so all is well now!!

  • georgei Jul 21, 2009

    lol ok im answering my own question... lol i got it it work im posting what i did for other ppl that have this same problem....



    i opened the cisco pix and reset the jumper that is in the middle of the board closed it back up and powered on the pix and started up... so all is well now!!



    thanks FixYa!!

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 30 Answers

Reload a new boot rom image

Posted on Dec 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an older Cisco PIX 506 with two VPN connections. One links two offices (PIX-PIX VPN) together, another is for staff to access email & files. The file server on the local LAN the PIX is on are...


It could be a missing route... are the file server and email server on the same subnet? If they are then it is possibly not a routing issue.

Also it would be worth checking the tunneling settings for the VPNs... if you have specifed either only the fileserver subnet or specifically the file server address, then this could be the reason they can get to nothing else.

Hope that this has helped a little :)

Apr 09, 2010 | Cisco PIX 506E 3DES/AES bundle (chassis,...

2 Answers

I need to connect cisco 2800 router to my pc through hyperlink


I think you mean hyperterminal? you need a cisco serial cable (blue) and a serial port on your PC, maybe a USB to serial adapter if there isn't one. Set hyperterminal to use the COM port you have plugged in to, speed 9600 8 bit no parity. (8N1).
Without the serial cable you need to know the router IP and password.

Oct 31, 2009 | Cisco (UBR904) Router

1 Answer

How to reset password of pix 506e


Hi,

You only need a PC and a serial terminal. First of all you need to know the PIX software version you run. After that you must go to Cisco web page and get from there the utility for the password recovery corresponding to your version of software.

After that you must connect to the PIX console port. Press ESC key after the PIX is booting and a special prompt it will appear (monitor>). Issue the "interface" command to specify which interface to be active. Inside interface it will be the default one. Then use the command "address" to go with the IP address of the above interface. After that, you will need also an TFTP server where you must upload the software utility specified in the beginning of the solution (the one downloaded fron Cisco). After the "address" command, issue an "server" command to put the IP address of the TFTP server. Than, use the command "file example.bin", where the example.bin is the file downloaded from Cisco. Maybe you will need also to specify the gateway of your network. This you can accomplish by using the "gateway" command. Finally, use the "tftp" command to start the download.
The default Telnet password after this process is "cisco."Go into configuration mode and issue the passwd your_password command to change your Telnet password.

Good luck!

Best regards,
T

Apr 24, 2009 | Cisco Computers & Internet

1 Answer

When Firewall powered on the Act/Net not enabling


jus login via console to the firewall and give the this command

Mentioned below is example give the interface number according to your firewall ports

conf t
interface ethernet0/0 100full if its a pix firewall

Mar 21, 2009 | Cisco PIX Firewall 506

1 Answer

My Pix 506E does not start


Can you please connect the console port with HT and post the boot script, I can them have a better idea of the problem.

Apr 02, 2008 | Computers & Internet

1 Answer

Protocol switching


Give each connection its own network & use Handshake authenication to access each other.You could also use a DMZ for 1(one) connection.
With this you will be able to use 1(one) External IP Address

Jan 08, 2008 | Cisco Catalyst 2924-XL Enterprise Edition...

1 Answer

ASA 5510 sec - bun k9


Basic Commands pixfirewall(config)#hostname PIX !--- Naming the PIX is optional. PIX(config)#nameif ethernet2 fo security20 !--- Naming the interface is optional. It is recommended that you !--- hardcode the speed/duplex. PIX(config)#interface ethernet2 100full !--- Bring up the interface. PIX(config)#ip address fo 192.168.1.1 255.255.255.0 !--- Assign an IP address. Failover Commands PIX(config)#failover ip address fo 192.168.1.2 !--- IP address for the failover link. PIX(config)#failover lan unit primary !--- This unit is primary . PIX(config)#failover lan interface fo !--- The 'fo' interface is used for LAN failover. PIX(config)#failover lan key cisco !--- The Pre-shared key. PIX(config)#failover lan enable !--- Enables failover. PIX(config)#failover !--- Start the failover process. This message appears on the console:
LAN-based Failover: trying to contact peer failover_01.gifLAN-based Failover: Send hello msg and start failover monitoring

Nov 27, 2007 | Cisco ASA 5510 Firewall

2 Answers

Upgrade firmware on a cisco ASA 5500 firewall


This is for the pixes, I haven't upgraded an asa yet...should be close or the same

* find latest version of code, these are usually *.bin files located on http://www.cisco.com/cgi-bin/tablebuild.pl/pix
* confirm the flash and RAM requirements of the PIX OS software versus what the PIX has (”sho ver”)
* make sure you have a backup of the old PIX OS and PDM to the tftp server (or at least confirm the software is there)
Note: You cannot back them up from the PIX, so you will need to download them and put them on the tftp server * put in a change control form
* once change controls confirms date/time do the upgrade:
wri mem*** only if you save your configs via tftp wri net conf t ca save all copy tftp://your tftp server ip/pix635.bin flash:imageskip this if you don't use pdm copy tftp://your tftp server ip/pdm-304.bin flash:pdm *** if this is a failover pair, upgrade the other pair reboot

Sep 06, 2007 | Cisco ASA 5500 Firewall

Not finding what you are looking for?
Cisco PIX Firewall 506E Logo

Related Topics:

479 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cisco Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Prashant M
Prashant M

Level 3 Expert

2260 Answers

brian soufane

Level 3 Expert

693 Answers

Are you a Cisco Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...