Question about Cameras

1 Answer

We bought model #109708 bell kidz training wheels and the instructions were thrown away before we could install. We are attempting to install on a Huffy girls coaster bike model #732626. Help!!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

We bought model #109708 bell - 82288_122206i.jpg
Is this what you are talking about? Or the entire bike?

If it is just these, they just snap together and bolt on where rear wheel is bolted on bike.
If you need more info, let me know and I will try to help you out.

Posted on Jul 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I bought bell trianing wheels and i have no idea how to attach them to the bike they did not come with any instructions


Unbolt the bolts on the rear wheel (pay attention to approximately the amount of torque to remove the bolts). Slide on the legs with a hole on one end and a curved end to fit the frame. Slide on the training wheels so the training wheel sticks out and is at an appropriate height for the bike. replace bolts with approximately the same torque as before. Also make sure the tire is seated as far back in the frame as possible to keep tension on the chain.

Jul 14, 2011 | Cycling

1 Answer

Instructions for bell riderz training wheels


Installing is easy if you take a look at the inside of the package! There are two nuts and a few washers on the screw that is used to hold the actual wheel. Make sure that you do not overtighten the first nut otherwise the wheel will not rotate freely. They appear sturdy enough. Only time will tell how much they will last!
Here is how to do the install:
1) Place the axle bolt through the wheel.
2) Thread one of the nuts on the axle bolt until it stops (use a flat washer here).
3) Put the axle through the frame. If there is a round washer, place it over the axle bolt next.
4) If there is a lockwasher, place it over the axle bolt.
5) Thread the other nut onto the axle bolt, then while holding the first nut, tighten the second one.
6) Install the assembly onto the bicycle.

Dec 25, 2010 | Cycling

1 Answer

Bell brand bicycle training wheels


hello there:
the training wheels are a simple procedure you will need to take the nuts off the back wheel and place the steel spacer and put over the axle then place the training wheel over the spacer and put the nut on making sure the the training wheels are not too low or too high.... best of luck to you hope the information is helpful

May 29, 2010 | Cycling

1 Answer

Need to install Lexmark 4350 all in one but lost disk


If you want to purchase a replacement disk.

Contact Lexmark here, to see if the disk for your printer is available.

If you do not have the disk you can also download the software from Internet, follow instructions below,

Click here:Official Lexmark Drivers and Software

A web page will open, follow instructions, select model, select operative system etc., and click on download .
Chose to download the file in my documents when asked.
After downloading, find the file,double click on the file ,then if you get in troubles, follow the instructions below to reset and reinstall drivers:

  • Unplug printer USB.
  • Go to control panel >> installed printers in Windows and remove (delete ) any installed printer from printer list.
  • Download driver from website, or use the disk and run the install file.
  • Follow driver installation wizard.
  • Plug back printer when prompted from installation wizard.

Apr 09, 2009 | Lexmark P4350 All-In-One InkJet Printer

1 Answer

Pictures out of center


No My Sons Does The Same Thing These Things Are Junk Sorry.

Jan 04, 2009 | Sakar Kidz Cam Digital Camera

Not finding what you are looking for?
Cameras Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cameras Experts

kakima

Level 3 Expert

102366 Answers

Steve

Level 3 Expert

3287 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Are you a Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...