Question about Exercise & Fitness

1 Answer

I have a DKN T210 treadmill, and when I switch it on I get error 04: ??? Does anyone have any idea what that could mean ?? Thanks in advance!!! ; Are I use google translate

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 6,694 Answers

If you wish to get some details about treadmill repair ; visit the site linked here. Pull up older posts.
http://electro-medical.blogspot.com/

Posted on Jan 02, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my t210 treadmill stop and then come up error e02?


Hi this is due to the treadmill's belt speed loss.

This happens if the motor is faulty or if the belt is stopped suddenly due to too much weight on it or misuse.

I would have the motor checked if I were you.

Feb 08, 2016 | Exercise & Fitness

1 Answer

Life gear error 3


Hi,
error 3 means the waking belt starts moving without any command. Make sure that you are not moving the belt manually before the treadmill stars .
for more details check the link
electronics repair help LIFE FITNESS T3 T3i T5 T5i T7i TREADMILL ERROR...

Feb 08, 2014 | Life Fitness T3 Treadmill with Advanced...

1 Answer

Davina treadmill motorised jx-622w wont start display says e00


E00 Means the red magnetic key (the one on the string) is not inserted.. If it is then the magnetic switch may be faulty.


E01 Is an electrical fault - the wire that runs inside the frame is probably crushed while assembling

E02 Means the motor is not running - either burnt out, stuck or the optic device is not functioning correctly.

This are what I found out by trial and error - hope its useful to someone - I'm looking for a copy of the manual for this thread-mill if anyone could send me a scan or photos of the pages - thanks very much.

Mar 17, 2013 | Exercise & Fitness

1 Answer

E5 error code on a YorkFitness Inspiration treadmill, anyone know what i should do?


key permanently stuck, remove the keypad connector cable. Restart the power up sequence, if the error disapear the keypad is the cause.
otherwise the PCA is the cause. the chip PCA must be changed.

God bless you

Jun 17, 2012 | Exercise & Fitness

1 Answer

I have no manual for my Fitstride T210 treadmill & would like to know where i put the lubricant oil??


go to www. fitness.manualsonline.com or www. iconservice.com

www. manualsfactory.com
God bless you

Jun 08, 2012 | Exercise & Fitness

1 Answer

A backwards E appears on my treadmill model 3-1-04-050 FH what does this mean?


Read your instruction manual, section troubleshooting for indication.

However you must adjut THE reed switch, see the diagram attached, clean, and tigh the connector wires very well. God bless you.
Run the software calibration for diagnose, and troubleshooting too.
6_8_2012_4_02_44_pm.gif

Jun 07, 2012 | Sportcraft Tx 455 Sportscraft Treadmill...

1 Answer

What's your problem?Hi i hav a York T500 treadmill and its showing error 04. What does this mean


Incline system VR(variable resistor) error First. Other causes included a bad data cable,drive board IC,and display IC.Some Diode LED light when the currend exceed the limit.

sincerely.

E.CUADRA

Nov 03, 2011 | York Barbell Home Use Fold-Up Treadmill

1 Answer

Error 7 on my york inspiration treadmill tried reset button but still not working any ideas.


hi,
By error 7 it means that the safety is not positioned correctly. or the saftey switch inside the unit is faulty. Its a magnetic switch. When you place the safety key (its made of magnet) this switch will activate. Then only teradmill start. Check the safety key is positined correctly or not. If it is in position then you have to replace the safety switch inside the control console.
OK

Sep 01, 2011 | York Barbell Home Use Fold-Up Treadmill

1 Answer

Hi just wondering if anyone can help with a problem with my York T500 treadmill. It comes up with error 03 in the speed panel. Any help would be appreciated. Thanks


hi,
Error E3 means speed sensor error.there is a sensor for checking and controlling the speed. check the speed sensor and its,connectors, clean the speed sensor. for that u have to open the motor cover.
ok

Dec 30, 2010 | York Barbell Home Use Fold-Up Treadmill

Not finding what you are looking for?
Exercise & Fitness Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Exercise & Fitness Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Howard
Howard

Level 2 Expert

115 Answers

Tom Chichester

Level 3 Expert

36514 Answers

Are you an Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...