Question about Washing Machines

1 Answer

F code on a cabrio wtw6400sw3 sounds like a bearing is going out

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Washing Mach... Master
  • 5,323 Answers

Its not an f code its an f code then u have to add the applICABLE NUMBER THAT APPLIES.

SEE THE LINK Whirlpool Cabrio Automatic Diagnostic Mode
Here are instructions for entering the technical diagnostic mode. This mode is designed for service technicians familiar with the product testing operation, if you need more instructions, you can find information on the tech sheet located inside the console of the washer as the entire diagnostic process cannot be published on this site. Always disconnect power supply before entering any closed section of the appliance and wear safety glasses and gloves.
1.Be sure the washer is in standby mode (plugged in with all indicators off)
2.Perform the following sequence of movement using the cycle selector knob.
3.NOTE: AFTER RESET, sequence must be completed within 6 seconds.
4.RESET - Rotate cycle selector knob counterclockwise one or more clicks to clear sequence.
5.a. Rotate cycle selector knob clockwise one click and wait ½ second.
6.b. Rotate cycle selector knob clockwise one click.
7.? Successful activation of Diagnostic test modes will be indicated by all status LEDs (except for Lid Locked) flashing ON and OFF in half-second intervals.
8.NOTE: LED names may vary between makes and models.
9.If the status LEDs do not display as described above, the sequence may not have been completed within 6 seconds. Repeat step 2 to ensure this was not the cause Whirlpool Diagnostic Mode

Posted on Jan 05, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a Whirlpool Cabrio washer WTW6400SW3 went thru wash wash cycle, then started to drain water to go into rinse cycle. Half way thru draining, was a loud electrical pop in control area of washer and...


sounds like a shorted machine due to water or moister? In most case you had a fuse blow on the machine somewhat like a thermal shut off fuse, most likely located in the panel. if this is the case u need to find out what shorted it, how water or moister got in? You can also look at the control curcuit board and look for burned seized transistors or areas indicating a burned out board.

Feb 11, 2015 | Whirlpool Washing Machines

1 Answer

What size is my whirpool cabrio washer wtw6400sw3


Whirlpool Cabrio 4.5 Cu. Ft. 11-Cycle Super Capacity Plus

Jul 07, 2014 | Whirlpool Cabrio Washing Machines

2 Answers

Need to know what the error codes mean on a whirlpool cabrio model wtw6400sw3 F54,F82,F83,F84. Please help.


you may have something between the tubs or your bearing is going bad . does it sound like a jet plane in spin cycle?

Feb 20, 2013 | Whirlpool Washing Machines

1 Answer

How to install whirlpool Cabrio bearing replacement kit


This Squidoo lens has videos and other info on how to install the cabrio bearing kit:

http://www.squidoo.com/how-to-replace-bearings-in-a-whirlpool-cabrio-maytag-bravo-or-kenmore-oasis

Jul 09, 2012 | Whirlpool Washing Machines

1 Answer

Washer will not fill on cold


http://www.searspartsdirect.com/partsdirect/part-model/Whirlpool-Parts/Washer-Parts/Model-WTW6400SW3/1198/0153200/W0810051/00002 Item 5 of the schematic is the water valve and is probably the malfunctioning component. Based on you description, but if there was more problems then I would suspect the electronic control (#1) or the interface (#7)

Jun 22, 2011 | Whirlpool WTW6400SW Cabrio Washer

1 Answer

The bearings on my Whirlpool Cabrio WTW6400SW3 make a racket on the spin cycle. The Whirlpool parts diagrams show that to replace the bearings, the entire drum is replaced. I can see one of the bearings...


Yes you can just replace the bearings but be careful. they say to replace the entire drum as the materials they are made out of is not very strong and you can distort or damage the drum when removing the bearings.

Oct 25, 2010 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Brad Brown

Level 3 Expert

15478 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...