Question about Kettler Exercise & Fitness

1 Answer

I have a Kettler Olympic 7892-000 treadmill that has just stopped working.

It started up ok, then stopped. I thought I had touched the encoder by mistake so tried to restart the treadmill, it counts down from 5 seconds but fails to start and after a minute or the display board flashes

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Kettler Master
  • 6,694 Answers

If you wish to get some details about treadmill repair ; visit the site linked here. Pull up older posts.

Posted on Dec 31, 2016


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My livestrong 10.0T starts but only runs about 5 seconds and shuts off

Check the speed senor. Align its potion or check is there is any dust accumulated on it,

If you wish to get some details; check the site linked here. Pull up older posts.

Sep 14, 2016 | LIVESTRONG by Johnson 10.0T Treadmill

1 Answer

My Sole F63 will slow down a few seconds after I start it then I get a low speed displayed on my control panel

please LUBE the deck belt+ rollers bearings too. You must do it evey 150 miles apros. This happen because the lack of maintenance schedule.
God bless you

Jan 21, 2013 | Sole Fitness Sole F63 Treadmill

1 Answer

I have a roger black treadmill the belt stops working after 5 - 6 minutes, the display still continues counting as normal, I have to wait for acouple of hours to start it again to last for 5 mins. please...

1) this a problem by lack of LUBE maintenance, you must LUBE about 5 hours continuosly of use. Otherwise you may have a worn DECK BELT, and time to replace. By that reason the treadmill shut down, to due the software has protection itself for electronic system
2) LUBE the rollers bearing.
3) test the bearing from the main motor, and replace too.
God bless you

Nov 14, 2012 | Exercise & Fitness

1 Answer

Keeps defaulting to pause every 5 seconds

1) replace the batteries, and clean the contacts batteries with c. cleaner
2) adjust the REED switch, see the diagram attached, clean it and tight the connector very well.
3) tight the ribbon cable very well inside, and clean it with c. cleaner with carefully.

God bless you

Sep 09, 2012 | Schwinn 250 Recumbent Bike

1 Answer

Samsung Dryer starts for 5 seconds then stops, but drying time still counts down.

I got the same problem and I tried to take off the belt let see the motor still running by itself but it still run for couple second then stop.

Jun 12, 2012 | Dryers

1 Answer

Error Code E7

To fix the error you have to put the safety key in start it it and wait for it to say E7. Now press stop and incline( up) together and hold for 20 seconds. Your treadmill will start to incline up. Take out your safety key. You just restarted your treadmill and can now put the safety key back and your problem will be fixed.

Apr 22, 2012 | Exercise & Fitness

2 Answers

Carl Lewis MOTC66 E03 error HELP !

Check the motor brushes if they are find then I would go back to the board regardless if its new it could be defective

May 04, 2010 | Exercise & Fitness

1 Answer

Treadmill tx400 wont work for llonger then 6 seconds

Sportcraft tradmill are very safe. First check and make sure there are no recalls on you unit. Do that on line or call Walmart where you most lickly got you treadmill. Try lubing you deck wich is under the belt. This is something that needs to be done to stop friction... Frition may have worn down the motor. Get back to me

Oct 10, 2009 | Exercise & Fitness

4 Answers

Tredmill error code e1

Trimline treadmill starts up then code E2 comes up, and the display shuts down. 
Any ideas???

Apr 02, 2009 | Nautilus Tr300 Treadmill

Not finding what you are looking for?
Exercise & Fitness Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kettler Exercise & Fitness Experts

Jim London
Jim London

Level 2 Expert

257 Answers

ray gallant

Level 3 Expert

49094 Answers

Steven Brandon
Steven Brandon

Level 3 Expert

460 Answers

Are you a Kettler Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides