Question about Honeywell Humidifiers

Open Question

Honeywell humidifier QuickSteam powers, digital commands adjusting works, but no heat no steam. Thermal fuse is OK.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Honeywell HE440A steam power humidifier

Honeywell has had lots of problems with this humidifier. They are coming out with a completely redesigned steam humidifier that will be available in a month or two. If you know who installed it (through equipment stickers and such) you can probably get them to swap your old trouble prone unit for the new design for just the labor. If they won't, then push them to talk with their Honeywell distributor about it.

The problem is most likely a stuck float in the humidifier. There are two floats that run up and down. One that tells it when to add water, and one that is a safety. They both tend to get stuck with mineral deposits.

You can fix it by unplugging the humidifier, turning off the water, draining the pan (unscrew the drain on the bottom a few turns), disconnecting the water lines and wires (2 molded plugs and 2 screw terminals-don't worry about if they get swapped). There should be a couple of screws that lock it into the ductwork such that when you remove the screws you can pull the whole unit out to see inside the water tank. Then just clean everything out well and put it back together in the same order.

You really do want Honeywell to get you a new humidifier though.

Posted on Nov 17, 2007

Ad
  • 3 Answers

SOURCE: Honeywell True Steam Humidifier

Yes you will want the out door sensor. The reason why is it is going to read the average temp outside and will adjust what you hum is producing due to the temp outside, that is so you dont cause condensation on your window. You can run it in manuel or auto but i would strongly reccomend to run it in auto.

Posted on Dec 08, 2008

  • 104 Answers

SOURCE: Am looking for the owner's manual for the

you can download here
http://rapidshare.com/files/225370310/4858c9fccc48b69c50a7b921cff38680.pdf.html


Posted on Apr 24, 2009

  • 1 Answer

SOURCE: Honeywell Natural Warm Moisture Humidifier Is On But No Steam?

I have the same problem and I have 2 of them fairly new. I can't seem to find out what the problem is either.

Stumped?????????

Posted on Dec 16, 2010

  • 4736 Answers

SOURCE: I need the operation manual

Here is a link to your Owners Manual that you can download and print. Please do not lose it, as this model has been discontinued by Honeywell.

http://www.honeywellcentral.com/ssi/pdf/honeywell-commercial/QuickSteam-OwnersManual.pdf

Posted on Mar 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater Element for Hunter Niteglo Humidifier is not working


Heating elements are pretty reliable. They usually have a thermal fuse or thermostat that will open before ruining the element. If your handy with a multimeter, you can check the continuity of the parts and the element itself.

Mar 04, 2014 | Hunter 35216 Warm Mist Humidifier w/ 1.2...

1 Answer

I need the operation manual for the Honeywell quick steam humidifier HWM335, 3 gal. please


Here is a link to your Owners Manual that you can download and print. Please do not lose it, as this model has been discontinued by Honeywell.

http://www.honeywellcentral.com/ssi/pdf/honeywell-commercial/QuickSteam-OwnersManual.pdf

Mar 23, 2011 | Honeywell QuickSteam HWM335 3 Gallon...

1 Answer

True Steam Direct Injection Model # HM506 service light blinks 6 times before remaining a solid color. What does that mean? I realise that the unit is detecting a system fault, would just like to know...


Remove and clean the water level sensor and see if this resolves your error. If cleaning doesn't do it, check the connector for buildup. If neither of the above works, you'll need to order a new sensor - I've gone through two in four years as the heat appears to crack the plastic housing, allowing water to wick up between the plastic and the contact, ultimately shorting it.

Feb 21, 2011 | Honeywell Power Humidifier: Furnace...

2 Answers

I cleaned my Honeywell Quicksteam 3 gal. Now it won't turn on. Yes I have pressed the reset button


after your resetting try to start by pressing on button or try to reprogram the setting on digital thermostat ok.

Feb 04, 2011 | Honeywell QuickSteam HWM335 3 Gallon...

1 Answer

I have a Honeywell Chronotherm III Thermostat and in instead of showing the temparature in the display it shows -AC. I've replaced the batteries, and tryied adjusting Temp up and down for cooling and...


It would appear to me that you have lost the 24 volt power supply to the thermostat. In referencing the manuals for this thermostat, available @ www.honeywell.com, I've found that when the thermostat is not connected to the wall plate (plate mounted on the wall, that the thermostat either snaps or screws into), it will display the -AC. This being said, either the thermostat is loose on the wall currently, or your 24 volt transformer has died. Hope this helps.

Dec 23, 2009 | Honeywell Power Humidifier: Furnace...

1 Answer

Two furnaces one humidistat help on wiring


Honeywell tech support is awesome here in Minneapolis, I think you need seperate humidistats but check with HW, number is in owners manual.

Nov 21, 2009 | Honeywell Power Humidifier: Furnace...

3 Answers

Humdifier wont work


I'm having the same issue

Jan 18, 2009 | Honeywell HWM-260 Humidifier

2 Answers

Humidistat installation question


I suppose you are looking at the do-it-yourself model. Depending on the wire that is run up to you Regular Thermostat from your furnace. You may have to run a seperate line for the Humidistat. A digital thermostat that does Humidity and Temperature is recommended. Or you could just place a Humidistat near the furnace room. A wiring diagram will come with the Humidifier discribing the different ways to wire it.

Jan 09, 2009 | Honeywell Power Humidifier: Furnace...

2 Answers

Honeywell True Steam Humidifier


Yes you will want the out door sensor. The reason why is it is going to read the average temp outside and will adjust what you hum is producing due to the temp outside, that is so you dont cause condensation on your window. You can run it in manuel or auto but i would strongly reccomend to run it in auto.

Jul 02, 2008 | Honeywell Power Humidifier: Furnace...

Not finding what you are looking for?
Humidifiers Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honeywell Humidifiers Experts

Dennis

Level 2 Expert

231 Answers

Simon Benzekri

Level 1 Expert

11 Answers

jdthefixer

Level 3 Expert

744 Answers

Are you a Honeywell Humidifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...