Question about Garden

Open Question

Mixture adjustment screw settings on a toro snowblower

Model 38130

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 65 Answers

SOURCE: flooding problem need to adjust mixture screw to correct setting

is air filter clean and what is your elevation?

Posted on May 05, 2009

SOURCE: I have a toro snowblower that quit running last

Hi
I have seen them go through the engine into the muffler. Did you check the valves if it damaged them. I would check for spark first if that is good put a tea spoon full of gas in the spark plug hole and try to start. If it fires you need to clean the carb. If not i would do a compression test that will tell you if the screw damaged anything.
Sam

Posted on Jan 08, 2010

  • 308 Answers

SOURCE: what is the oil to gas mixture ratio on 1995 Toro

The proper mix is 50:1. The link to the manual is
http://ourfamilys.deandrea.net/BobKitty/User%20Guides/tosnowss.pdf

The fuel mixtures can be found on page 11. Hope this helps.

Posted on May 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I put a mixture of oil gas in my 621 R/621 toro snowblower?


Hi Jerome:
Shouldn't be too bad.
You could disconnect the fuel line at the carb and drain the tank.
Drain and flush the carb. Reconnect the fuel line and fill with fresh gas.
If it won't start, pull the spark plug and clean/dry it with a propane torch, or replace it.
Odds are it will be fine.
Cheers.

Jan 18, 2016 | Toro Power Clear 621 R Snowblower - 38451

2 Answers

Toro 824 snowblower starts fine but won't keep running and new gas new plug as well cleaned the whole carb


Is there an adjustment screw on the carburetor if there is turn it out a little at a time. This sets the amount of gas going into the carb and lets it run the way it should. I hope you have one as this is the answer to many engine problems. When you say you cleaned the whole carb did you clean the fuel jet. It won't run if the jet is dirty.

Feb 06, 2015 | Toro Garden

1 Answer

I have a Toro 524 with Tecumseh engine, model 38040 8 0000640. I am rebuilding the carb and would like to know what are basic settings for idle and hi/low speed screws?


The high speed mixture screw is initially set at 1 & 1/2 turns out. Then adjust it to give good acceleration and top speed, while not closing the screw more than you need to. The low speed mixture screw is set at 3/4 of a turn out. Adjust that, to give a smooth idle. The 3rd screw, the idle speed screw, is set to give a low idle speed without stalling.

Jan 14, 2011 | Toro Blowers Rake and Vac - Electric...

1 Answer

I have a toro snowblower with a 2 cycle engine. When it's just running under no load it seems fine(maybe a little too high of rpm). When it starts throwing snow it gradually slows down until it quits...


It sounds like it is running lean. Back out your carbuerator adjustment screws a quarter turn counterclockwise. These settings should be 1 and a quarter on low speed (closest to engine block) and 1 and a half on high speed (farthest from engine block). These are starting points the adjustment may vary a little eigther way. Never adjust for max rpms that is too lean and will cause engine failure. Hope this helps ya.

Dec 22, 2010 | Toro Garden

1 Answer

I have a toro snowblower that quit running last year. The screw which held the choke plate in place is missing and I can't find it. Is it possible the screw is in side the motor? I removed the carburater...


Hi
I have seen them go through the engine into the muffler. Did you check the valves if it damaged them. I would check for spark first if that is good put a tea spoon full of gas in the spark plug hole and try to start. If it fires you need to clean the carb. If not i would do a compression test that will tell you if the screw damaged anything.
Sam

Jan 08, 2010 | Toro Co M/R Blwr/Trmmr Rear Bag Kit

1 Answer

How to set up a carb with 31840 rebuild kit


what exactly do you want to know? Carb. mixture settings are as follows: L-head engines

Tecumseh carbs.........mainscrew 1 3/4 turns idle screw 1 1/4 turns
Walboro carbs........... mainscrew 1 1/2 turns idle screw 1 1/4 turns

L-head and OHV heavy duty engines 1 turns for both

Dec 21, 2009 | Toro Garden

1 Answer

Toro snowblower///// tecumseh# on motor is H35-45598R SER 5283B


Usually that is a sign of the carb not being adjusted right. Run it at full throttle and adjust the main mixture needle (usually on the bottom) until it runs the smoothest. Set it in the middle of the range where it runs smooth. Then set it down to idle and adjust the idle mixture until it runs smooth at idle. Accelerate it rapidly and if it bogs or hesitates turn the idle mixture a little leaner (clockwise) and try again until it works right. That should get you very close. Try tweaking it a bit from there. as the microscopic specks clean out of it, it may need more adjusting.

Nov 25, 2009 | Garden

2 Answers

I have a Toro s 200 model 38130 1979 snowblower. it would not prime no suction when bulb pushed. I replaced the diaphragm with a kit diaphragm first to carb etc. along with new needle valve and spring. Now...


snowblower no fuel . pull float bowl from the bottom of carb the bolt you removed from the bottom to take off the float bowl there will be a small hole in it take a needle make sure to clean it out . then clean out where it threads into .

Dec 03, 2008 | Chevrolet C1500 Cars & Trucks

Not finding what you are looking for?
Garden Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2478 Answers

john h

Level 3 Expert

12104 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...