Question about American Standard Home

Open Question

Serial no. 6495853 model no. 7236L020

This is for Ana American Standard Whirlpool tub and I am looking for replacement parts

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
arealplumber
  • 33 Answers

SOURCE: american standard whirlpool tub #2425

Here is the link to installation instructions:

American Standard #2425

The information you need is on page #7.

Hope this helps!

Posted on Dec 05, 2008

Ad
  • 7 Answers

SOURCE: Whirlpool pump only buzzes.

Well there are two things....You say "buzzes?" Like pump is running "humming" & not pushing water. That would be an "airlock" in the pump & it needs to be primed.
If it's "buzzing" & pump motor is not turning (Like it's froze) you might have a bad start up capacitor on the pump that needs to be replaced. Worst case scenerio entire pump needs replacement.

Posted on Jan 14, 2009

PartsCenter
  • 125 Answers

SOURCE: I bought American Standard whirlpool

no manual. Sounds like the motor is no good. What model and brand of pump do you have?
replacement Bath Pumps

Posted on Feb 24, 2009

  • 62 Answers

SOURCE: We have an American Standard lifetime whirlpool

Chances are that the drain assembly was not part of the tub but a 'generic' plumbing part. Is this pop up drain the type that you push down and it clicks closed and push down and then it pops up? It unscrews from the drain fitting and you can get a replacement at a big box store. A better pop up replacement is one called a Rapid-fit. It drains faster.

Posted on Jun 05, 2009

  • 23 Answers

SOURCE: Button on American Standard Whirlpool tub is stuck

most tub buttons are attatched to a small air tube thats connected to a switch. if that tube came off the button wont work. just look inside your access panel the tube will be there check both ends if one came off vut 1/4 inch off and reattach

Posted on Jul 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have an American standard whirlpool tub. the on/off button is stuck on on. now the only way to shut the jets off is to flip the breaker to the bathroom. how do I fix this


This sounds like the air switch in the motor is not working properly. You will need to remove the pump from under the tub to access the air switch located in a housing on the motor.
Replacement Air Switch will cost you about $20

US Parts Center

Aug 27, 2013 | American Standard Home

1 Answer

We have an American Standard whirlpool tub. It's probably about 20 years old and we haven't been able to find the model name or number. It's about 4' by 5'. Our problem: we don't...


you have to access the lower control the switch should be an air type one it uses air pressure from pushing in the button they some times crack ,dislodge or damaged and will not turn on or off unit also switch can fail

Jul 12, 2017 | American Standard Cambridge 5 Ft. x 32"...

1 Answer

My American Standard Whirlpool does not turn on. I push the Power button and don't hear anything. Circuit breaker is on, anyone have any ideas? Thanks!


Remove access panel make sure pump is plugged in some electricians put a GFI outlet under tub for motor make sure GFI did not trip. Next the switch is an air switch look for the hose going to switch is connected last you may need a new air switch which is common to fail

Nov 03, 2009 | American Standard 2770.018w.020 Cadet...

1 Answer

My American Standard whirlpool pump will only hum.


The bearings (or bushings) of the pump or pump motor have siezed, these can be replaced on some models but for the most part you will need to replace the pump and/or pump motor. and as where to get parts, i would suggest the outlet from wich you purchased the unit or another appliance outlet. Or if you feel up to the challenge, im sure you could find replacement parts on the internet: google, ebay, etc.

Sep 29, 2009 | American Standard 2770.018w.020 Cadet...

1 Answer

We have an American Standard lifetime whirlpool tub with the pop up drain (white). However, the pop up drain plug has always been tempermental but now it no longer wants to stay down.


Chances are that the drain assembly was not part of the tub but a 'generic' plumbing part. Is this pop up drain the type that you push down and it clicks closed and push down and then it pops up? It unscrews from the drain fitting and you can get a replacement at a big box store. A better pop up replacement is one called a Rapid-fit. It drains faster.

May 12, 2009 | American Standard Evolution 1599.205.020...

Not finding what you are looking for?
Home Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top American Standard Home Experts

Donni Steen

Level 3 Expert

659 Answers

Mike

Level 3 Expert

4340 Answers

john h

Level 3 Expert

12650 Answers

Are you an American Standard Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...