Question about Maytag Dishwashers

Open Question

Maytag dishwasher start light flashing, won't respond

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Maytag Dishwasher will not start.

I had the same problem. The plastic wiring strip that connects the touchpad had corrosion from water. The panel would need to be replaced, because they don't sell the touchpad separately. (around $50 - $70 USD)

Posted on Jun 06, 2008

Ad
  • 1 Answer

SOURCE: DISHWASHER WON'T START,ALL LIGHTS ON PANEL FLASH RED

how to download the game gat4 (i don't know ENGlish )

Posted on Feb 15, 2009

  • 1 Answer

SOURCE: Green Lights flashing, Whirlpool D/Washer not responding

Well I contacted a couple of techy guys I know and they were not familiar with the dishwasher. I then called the outlet we had purchased from to see if they could refer us to a service technician. I explained what I wanted and the woman on the phone asked what the problem was - she then asked me to close the door of the dishwasher and hold down the start button for 30-40 seconds to see what happens, which I did. At about the 30 second mark the machine started. She said it was likely that someone had interrupted the last cycle and we had effectively reset it. It ran a further 30 seconds to complete that last part of the interrupted cycle and has been fine ever since. My wife took them a box of chocolates the next day. Shows to go ay? Kind regards Peter

Posted on Dec 30, 2009

KevinWhite
  • 1902 Answers

SOURCE: My maytag dishwasher won"t start

Hello & Welcome to FixYa

First clean the drain filter pump assembly located inside the front bottom access panel. If the problem is still there after cleaning the drain filter assembly then it means the control board is bad and needs replacement. Please get back to me if you have any other questions.

Kevin

Posted on Jun 14, 2011

  • 1010 Answers

SOURCE: Dishwasher won't start and start button doesn't light, but other buttons respond

I think you still have warranty, it sounds you have faulty control panel, even if it's new does not mean it is good.

Posted on Mar 19, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Maytag dishwasher mdbtt53aww2 will not start. The right side of the panel lights up. The left side does not light up. Anyone know what it might be???


Many electronically controlled appliances respond well to a simple reboot. Pull the plug and put it back in.

Report back!

Oct 25, 2016 | Maytag Dishwashers

1 Answer

After a few minutes into cyle delay lights start flashing


Light(s) Flashing/Blinking - Door Opened - Delay ... - Maytag

www.maytag.com/...light(s)-flashing-blinking...delay.../PH7053/
MaytagQuestion: Built-In Dishwasher - Light(s) Flashing/Blinking - Door Opened - DelayWash - Cycle Power. Answer. Product Symptom: Built-In Dishwasher - Light(s) ...

Sep 26, 2015 | Bush Dishwashers

1 Answer

How to reset control panel mdbh979sam1


My Maytag Dishwasher - Will not Start or Complete a Cycle - MDBH979SAM1- the lights keep flashing but will not start.

Jun 22, 2014 | Maytag Dishwashers

1 Answer

Maytag dishwasher will not start


REPLACE THE DOOR SWITCH.....NOT GETTING RUN COMMAND CAUSE SWITCH N DOOR NOT BEING MADE

Oct 15, 2013 | Dishwashers

1 Answer

Dishwasher won't start and start button doesn't light, but other buttons respond


I think you still have warranty, it sounds you have faulty control panel, even if it's new does not mean it is good.

Mar 19, 2013 | Kenmore Dishwashers

1 Answer

Maytag dishwasher Model MDB7749AWB won't start/respond


Either the start switch, the start relay, the wires between them, the wires to the motor, or an internal fuse inside the panel, or the door safety interlock could be the problem. Even, any combination of the above could cause this. This is a real troubleshooting problem. Are you game?

Dec 28, 2012 | Dishwashers

1 Answer

I have a maytag dishwasher theres a 3 second button to hold in order for it to start but it won't start it's stuck on 3 second lite


hold the heated dry button for till that light goes out. then try to start. it is a child lock that is on

Oct 08, 2011 | Maytag MDB7100AWB Dishwasher

1 Answer

I press the "start" button and the "2Hr" light just keeps on flashing. unit does not start. then light goes out.


do you have a maytag? just curious
sounds like you have a bad touch panel
if you can not control the keypad and no keys respond, you have a bad keypad

Aug 24, 2010 | Dishwashers

1 Answer

The heated dry and clean lights flash together


I had this same problem. I read on another blog that the manual recommends that you turn the power off to dishwasher. When you turn the washer back on, the lights still flash but then push the off button. The lights stopped flashing.

Jan 15, 2009 | Maytag 24 in. DWD1500A Built-in Dishwasher

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Charles T Nevin
Charles T Nevin

Level 3 Expert

4066 Answers

Mike

Level 3 Expert

4340 Answers

Are you a Maytag Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...