Question about Panasonic VIERA TC-P50U50 50-Inch 1080p Full HD Plasma TV

Open Question

Panasonic plasma TV model TC-P50U50 When turn on TV flashing once and turn off itself. What is it?Power supply?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: I HAVE A PANASONIC PLASMA TV TH-50PZ80U MODEL #.

With this symptom, it is impossible to tell what the exact "Cause" of this symptom is. The LED's do not tell us what is wrong, sometimes it may indicate the "Area" in your case it is the X board. BUT thats NOT where the "Fault is" thats just the part that is affected. These days unlike the "Old" analogue days it just isn't realistically possible to fix anything but the most basic of problems with todays sophisticated units. This is quite apart from the Safety aspect, any unit that can cause a firs or have an explosion, or both, is NOT to be treated lightly, and and the repairer, of the unit is legally responsible, another thing to think about. Also, one must have tools, a Multimeter, a soldering iron, a deslodering iron, an oscilloscope, a signal tracer, tools, and most important of all, a Service Manual, without which, there is no way to even begin to understand and fix it, and more importantly Program it, AFTER it has been fixed. As these days a TV, is a PC, a Tuner, and an HDTV Monitor, and more, all in one. in the "old" days TV"s were more, rudimentary, and built to last for 20 years, and a "Parts" supply was set aside. They usually used to fail for only a few reasons, and they while still difficult, were less difficult to repair. Electrical knowledge was transferable, and they could be and would respond to, This-is-the-symptom-This-us-the-Fix, But that no longer applies, as now, it can be a Fault on I squared Bus, or "Sensor" failure, or it simple may have "Crashed" just like a PC, It could be a Diode go bad, and that will stop the whole thing. You see, in the day, the sets were Very "Fault Tolerant" because they were Analouge, and a faulty, component, or more sometimes, the set would always diplay something usually, and when they didn't it was one of anly a few things, sure there are always the horrid ones, and there are pleanty of those, but all in all it was quite easy. But with Digital Electronics, it either goes, or it doesnt, there are usualy few half measures. I mean thats the definition of logic either going or not. So it can take very little to completely paralyse a set, and generally give the only sysmptom, it can, by not working, usually No picture, or the like. So you, see the list is endless almost for any given SYMPTOM, as that is what is being seen, not the cause, as I keep going on about. Also any fault, usually involves the Power Supply, it is either the cause, the cause of the damage, or it is damaged. or ALL of them. Then after you have done the electronic repairs, you then must program the set to work, and align, and set up in general, any one of those settings missed or done wrong, back to square one. So, it is nearly always my professional opinion that one should always get a "Quote" form the manufacturers recommended service center, I cannot stress how important that last point is. It is even worth the cost of shipping. you see an authorised service agent, will have trained staff, trained on their brand, also they have first hand access to parts, original parts. This will actually save you money and ensure you can actually get it back fixed. Of course asking for a "Quote" also gives on the option of repair or replace. Often my clients,do not go through with repair, unless it is moderate, but in some of the more costly jobs they see it, as do i, that a replacement, with a warranty, is a better option. As an aside here, one could then tear the TV down, and sell the Known Good bits. You'd be surprised who needs parts, i myself often must by from third party sources to effect a repair. So money could be recouped, somewhat,and help out someone else. Anyway thats my 10c worth.

Posted on Apr 02, 2010

Ad
  • 1 Answer

SOURCE: I have a panasonic plasma tv. Model #

I don't know but I'm having a similar problem. I have a plasma
TH-50PZ77U. It will run for a while and then shuts off. Also, the volume goes up and up and then it shuts off at times. Like I have a ghost here. I had both of my sat. recievers replaced. It seems to get worse over time with shut down. I called panasonic and they had no info and denied this was an issue but I beg to differ from my research here online. It's only a few years and we paid lots of $$$. They gave me a # for service 1 hour away!

Posted on Jul 11, 2010

  • 184 Answers

SOURCE: Panasonic viera Plasma TV model TH-P42X10A The tv

Hello,

The power supply board of the television is dead, u know basic electronics' and soldering? Most of the times, the power supply board just have dead leakages gases capacitors.These capacitors always bulges up on it top,or puff up on it top.Replaced these gases leakages capacitors will get your TV power stable,and work again.Or tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.

I hope this will help in solving the problem....

Posted on Aug 01, 2011

palaboy
  • 5807 Answers

SOURCE: I cant connect to the internet I have the cable going directly into the TV and I still cant connect to the TV can someone tell my why?

It is sad to say that Panasonic - 50" Model: TC-P50U50

lacks the ability to connect to internet.

It should have an Ethernet port.

Posted on Sep 29, 2012

gopakumarg43
  • 74211 Answers

SOURCE: I have picture but no sound from my Panasonic

Check and replace its speakers, or damaged component/s at its audio output stage circuit. For more details, check this link. http://electronicshelponline.blogspot.com/
Pull up previous posts by its left sidebar, or type in the brand name and model number to of your set, to its search box, and press 'Enter' or view it in Mosaic / Timeslide option.

Posted on Sep 25, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Panasonic TV, Model TC-P505U50


Not sure if it is Plasma or LCD/LED model.
Check out the codes below
Panasonic TV Blink Codes for All Panasonic Models Brainchamber Blog

You need to verify the Power board for defective capacitors. You can replace the defective Capacitors yourself if you are a DIY person or replace the entire board if you can obtain the part.

Aug 01, 2016 | Panasonic Television Mainboard, TV Model...

1 Answer

How do I fix a 50 Plasma TV that seems was struck by lightning


Your probably have power supply damage, but lightning strikes can do major damage in all circuits.

Aug 07, 2015 | Panasonic VIERA TC-P50U50 50-Inch 1080p...

1 Answer

Panasonic viera turn


The problem could be power supply failure.

Jul 17, 2014 | Panasonic VIERA TC-P50U50 50-Inch 1080p...

1 Answer

I have picture but no sound from my Panasonic TC-P50U50 plasma TV, what is wrong?


Check and replace its speakers, or damaged component/s at its audio output stage circuit. For more details, check this link. http://electronicshelponline.blogspot.com/
Pull up previous posts by its left sidebar, or type in the brand name and model number to of your set, to its search box, and press 'Enter' or view it in Mosaic / Timeslide option.

Sep 25, 2013 | Panasonic TC P50U50 - 50" Class 49.9"...

1 Answer

Tc-p50u50 cracked screen


It is not worth it to replace the screen. I found that everyone recommends scrapping tv or finding another broken tv and using that screen.

Apr 22, 2013 | Panasonic TC P50U50 - 50" Class 49.9"...

1 Answer

I cant connect to the internet I have the cable going directly into the TV and I still cant connect to the TV can someone tell my why?


It is sad to say that Panasonic - 50" Model: TC-P50U50

lacks the ability to connect to internet.

It should have an Ethernet port.

Sep 29, 2012 | Panasonic Viera TCP50U50 50-inch Plasma TV

Not finding what you are looking for?
Panasonic VIERA TC-P50U50 50-Inch 1080p Full HD Plasma TV Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5126 Answers

kakima

Level 3 Expert

102366 Answers

Michael Kovalik III
Michael Kovalik III

Level 2 Expert

117 Answers

Are you a Panasonic Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...