Question about Frigidaire FEF376 Electric Kitchen Range
Door is open lock is on and will not unlock
SOURCE: frigidaire range
I had a similar problem. Turned out that the locking road hung up and the motor wasn't powerful enough to move it. So I removed the two screws that hold down the cooktop and freed up the locking rod. Then I turned the range back on with the door open, but holding in the door switch as if it were closed. the lock then completed its locking cycle. Then I was good to go. Hope this helps somebody else.
Posted on Jan 29, 2008
1. Verify error code by pressing and holding CANCEL/OFF key for 5 seconds.
Momentarily (less than 5 sec.) press CANCEL key again to remove error code
2. Press and hold any key for 1 minute until F2 E0 code is displayed.
3. Cancel F2 E0 error code.
4. Program and start the clean mode. Observe to see if door locks. If it does not,
inspect the locking mechanism from the solenoid to the latch pawl and door to
find the cause of the problem. If the door is not locking, then 1 minute from the
start of clean, the F5 E1 code will again be displayed. Steps 1 through 3 will
have to be repeated before another clean can be started.
5. Once any mechanical problems with the latch mechanism have been corrected,
program and start a clean cycle (after, if necessary, clearing F5 E1 error code)
to ensure proper operation of the door lock. Immediately cancel the clean mode to observe proper operation of door unlock
Posted on Feb 12, 2008
SOURCE: frigidaire oven door locked
SOME RANGES ARE DESIGNED TO LOCK IF THE CONTROL SENSES A TEMPERATURE EXTREME. IF THERE IS A FAILURE OF THE SENSOR THAT MAKES THE CONTROL THINK THE TEMP IS UP, IT WILL LOCK THE DOOR TO PREVENT INJURY. REMOVE THE BACK PANEL AND FIND THE OVEN SENSOR LEADS COMING OUT THE BACK OF THE OVEN. DISCONNECT THE SENSOR AND CHECK THE RESISTANCE. AT ROOM TEMP IT SHOULD BE SOMEWHERE AROUND 1084 OHMS. IF IT IS NOT CLOSE,
THE SENSOR IS BAD. PLUG IN A NEW SENSOR AT THAT CONNECTOR AND THE DOOR SHOULD UNLOCK. THEN GET INSIDE THE OVEN, REMOVE THE OLD SENSOR, AND REPLACE IT WITH THE ONE PLUGGED IN.
Posted on Apr 04, 2008
SOURCE: frigidaire range
Unplug the unit, then manually depress and hold the light switch on the frame of the unit while plugging it back in. The lock should go back into the proper position.
Posted on Dec 25, 2008
The "F9" error code means the EOC (electronic oven control) has found the lock motor switches to be out of sequence or shorted.
Test switches and if there is nothing wrong then replace the EOC.
Posted on Oct 16, 2009
Tips for a great answer:
I appreciate your post, friend!
Based off the information you have provided the door on your Frigidaire range will not unlock. I would suggest performing a reset on your range and you can do that by flipping the household circuit breaker off for roughly ten minutes. If that does not work you can attempt to start another clean cycle and right before it starts press the cancel button. If neither trouble shooting step unlocks the door your latch may be broken. I would then recommend having a professional technician perform a diagnosis and repair. I hope this helps. -Matt
Feb 27, 2015 | Frigidaire Kitchen Ranges
Good Morning Kay Warren, I appreciate your post!
Based off the information you have provided the door on your Frigidaire range is locked and will not open. If you look on your control panel you should see a clear or cancel button, hold that down for three to five seconds. This should unlock your door. If this does not unlock the door you can attempt to perform a reset. You can do this by disconnecting the power from your range for ten minutes. I hope this information is helpful. -Matt
Dec 26, 2014 | Frigidaire LGEF3043KF Electric Range
Hello Yves Trottier, thank you for your post!
I understand that your Frigidaire range is displaying the error code "F93". Typically, "F93" stands for maximum over door unlock time exceeded. This could be a potential issue with EOC (Electronic Oven Control), motor door latch assembly, or fan motor. I would recommend performing a reset on your range which consists of you disconnecting power from the range for approximately ten minutes. If you continue to experience such issues I would suggest consulting with a professional technician for proper diagnosis and repair. Hope this information is helpful. -Matt
Dec 06, 2014 | Frigidaire Kitchen Ranges
Sep 10, 2014 | Frigidaire Kitchen Ranges
Apr 11, 2010 | Frigidaire FES367 Electric Kitchen Range
Aug 24, 2009 | Frigidaire FEF336BC Electric Kitchen Range
May 23, 2009 | Frigidaire FGS365EC Stainless Steel Gas...
Oct 10, 2008 | Frigidaire Gallery GLEFM397DS Electric...
May 10, 2008 | Frigidaire PLEF398AC Electric Kitchen...
67 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: