Question about RTO Paslode 902000 IM250 Ii Cordless 16 Gauge 3/4 2 1/2 Inch Straight Finish Nailer

1 Answer

I took my paslode im250ii apart and can not figure out how all the parts go together. I took off the rail assembly and parts went flying. Anyone have a schematic of how all this goes back together?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 384 Answers

Throw all the parts in a clothe dryer, in time they will assemble themself....may take years.

Posted on Jul 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Paslode 900400. Is there a video that shows you where to install the negator spring?


On this model the negator spring sits right inside the nail carrier - the end with the hole is held in by the front magazine screw.
http://www.paslode.com/uploadedFiles/IM250II%20schematics.pdf
25416499-2uullkphcfghqh054hptqowc-5-0.jpg

Feb 11, 2015 | Tools & Hardware - Others

1 Answer

How do I replace the upper probe assembly #78 in my paslode finish nailer IM250


With the old IM250 (900400) you remove the lower probe, open the nose release, the upper probe will turn slightly and come out.
With the newer models you have to disassemble the tool and separate the handle halves to remove the probe.
http://www.paslode.com/uploadedFiles/IM250II%20schematics.pdf

Sep 22, 2014 | Tools & Hardware - Others

1 Answer

[Paslaod 404466] How to put the magazine back together?


if this is the part I am thinking of it goes under the metal plate that lays in the housing you would need to have the tool in half and lift the plate and you will see a recess where they fit. if you are looking at the back of the gun it would be the left side of the housing. You can also try going to paslode.com and downloading a breakdown.

Jan 31, 2012 | Paslode Air Tools & Compressors

1 Answer

Reset button or Fuse on my Infinity?


Ok, I took it apart, cleared the clog out, and put it back together. It wouldn't switch to "carpet". Got no answer on my question. Took it apart again, only I went further. Took apart the bottom - brush out, all inside bottom parts out, cleaned all that part of vac. No clogs down there. Ran the carpet/bare floor switch back and forth several times while I had it apart. Put it all back together and it worked fine. Still didn't find a fuse or reset button...

Jan 09, 2010 | Vacuums

3 Answers

Friend took my 900420 nailer apart to clean it and when he got done, had a small spring about 3/16" x 1" left over. Does anyone have a clue where it might go?


Thin spring?
Goes in-between the Follower Guide and Button.
There are several Coil springs used in a Paslode 900420 framing nailer.

1.In-between the Upper Probe and the Lower Probe.
(Safety device you depress so the gun will shoot)
2.Trigger
3.Lockout Bar
4.Follower Guide and Button

(There is a flat spring also. Goes in-between the Probe Stop and Probe Release)

Here let me show you,

http://www.paslode.com/uploadedFiles/Cordless_Framing_Nailer_Parts_Diagram_Schematics.pdf

Oct 17, 2009 | RTO PasLode 900420 Impulse Framing Nailer

1 Answer

My paslode will not drive a 3 1/4'' nail in pine lumber, but it will drive a 2'' nail in the same lumber. i have took it apart and cleaned it with the paslode cleaner and used the paslode oil put it back...


check your air tank for moisture , drain it and put a oiler on it, or just oil it your self. put at least 3 to 4 drops run the proper amount of air they want you to run.

Jul 25, 2009 | Air Tools & Compressors

1 Answer

I cant get the head of my framing nailer back together


Go to Paslode website and get the parts breakdown/schematic. Making sure that everything is right way. This problem is a tad tricky. Trick is don't get mad or discouraged. The gun will win. Lemme know if you need anymore help. Pleas rate me.

May 26, 2009 | RTO PasLode 900420 Impulse Framing Nailer

1 Answer

Need complete assembly instructions!


have a greco bassinet from 2001 model no. 5610nr and lost assembly instructions can you provide?

Mar 08, 2009 | Graco Bedside Bassinet 5840 Crib

2 Answers

Icemaker auger


To see how the auger goes back together, go the the Sears parts web site and put in your model number. It will show the parts list and a diagram. You may be able to print it out, Don't remember if there is a print option or not but if you have a screen capture program you could also.

Apr 13, 2008 | Whirlpool EL7ATRR Refrigerator

Not finding what you are looking for?
RTO Paslode 902000 IM250 Ii Cordless 16 Gauge 3/4 2 1/2 Inch Straight Finish Nailer Logo

Related Topics:

218 people viewed this question

Ask a Question

Usually answered in minutes!

Top RTO Tools & Hardware - Others Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

yadayada
yadayada

Level 3 Expert

75016 Answers

Brad Brown

Level 3 Expert

15442 Answers

Are you a RTO Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...