Question about Measuring Tools & Sensors

1 Answer

My Smart Gear STG-6007-BB weather station won't pick up the outdoor temperature from the remote sensor. I changed the batteries and reset the unit, but it still doesn't work. Any suggestions?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Master
  • 44,073 Answers

  • Remove all batteries
  • Install batteries in remote sensor. Allow time for it to begin sending temperature information
  • Install batteries in indoor unit. You should see temperature displayed
Cold weather can cause loss of temperature information

Posted on Dec 17, 2016

  • Bob Isaacs
    Bob Isaacs Dec 17, 2016

    Thanks, Tom. I have the indoor unit plugged in to an electrical outlet. I changed the batteries in the remote, but it still doesn't work. Cold weather not the issue. I'm in Florida.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Smart Gear STG-5939-KB, Weather Station does not indicate the correct day. Instructions say it will adjust to the date. The date is 5/4 but the dat says TUE. Any ideas?


Your Smart Gear Weather Station may be defective. I have an atomic lock that indicate DST all year round but changes time correctly. One other thought: your weather station may be set for the wrong year.

May 04, 2018 | Measuring Tools & Sensors

1 Answer

I have the Atomic Clock model W86111. I had to change the batteries on the outside device. The clock outside temp just flashes 63.5 all the time. How do I make it sync to the device outside?


Remove all batteries from outdoor sensor and weather station.

Press one of the buttons on the weather station at least 20 times to clear all memory.

Verify that the weather station is blank before proceeding (there may be lines painted on
the screen that will show when power is removed).

Leave both units without power for 15 minutes (very important).

Insert fresh batteries into the clock.

Insert fresh batteries into the outdoor sensor.

Press the TX button on the outdoor sensor to transmit RF signal.

Keep the outdoor sensor 5-10 feet from the forecast station.

When RF connection is established, the temperature will appear on the station. Allow the
outdoor sensor and weather station to sit together for 15 minutes to establish a strong
connection.

Oct 14, 2017 | Home

1 Answer

31215 Wireless Outdoor Thermometer manual


With mine, the battery in the weather station has to be changed twice as often as the one in the external unit. Even though the display on the home unit is visible, it doesn't have enough power to pick up the signal from the outside sensor.

I am not familiar with yours, mine is national Geographic.

The reviews on yours are very mixed, but lots of questions are answered.

Amazon com Weather Station with Wireless Outdoor Thermometer 31215 Home...

Jul 24, 2016 | Measuring Tools & Sensors

1 Answer

Outdoor sensor won't work. Tried changing battery, no luck. Been trying this on and off for weeks. Any suggestions?


Some brands of Wireless thermometers need to have the base station reset to synchronize with the remote sensor. You would need to take the batteries out of both the remote sensor and the base station and then re-install all the batteries in both units (or three units if you have more than one remote sensor)
Each Manufacturer has their own procedure, La Crosse needs the procedure I described on many of their older systems. They may have changed it on the newer systems because I HATED resetting everything every time I change one set of batteries.

Feb 18, 2016 | Measuring Tools & Sensors

2 Answers

Why can't I receive input from the outside sending unit?


Make sure that all the batteries are good!!
This procedure outlines the typical process to pair the sensor and base.
Base Station Battery Installation

·Remove the printed vinyl label from the LCD screen of the base station
·Position the remote sensor near the base station
·Open the battery compartment at the back of the base station and insert (2) AA batteries according to the polarity markings. Replace the battery compartment cover.
·Within a short time the RF signal icon (located to the left of the outdoor temperature channel indicator) will start flashing. This indicates that the base station is ready to pick up the RF outdoor temperature signal from the remote sensor. It will continue to flash for 3 minutes or until the signal from the remote sensor is detected.

Register the Remote Sensor
·Open the battery compartment at the back of the remote sensor and slide the channel selector switch to your desired channel. For the first remote you may select any channel, for additional remotes select any unused channel
·Insert (2) AAA batteries according to the polarity markings. Be sure to install the batteries in the remote within the time that the RF signal icon is flashing on the base station. 1541 WeatherGuide Wireless Weather Forecaster with Barometer

Jan 07, 2016 | Measuring Tools & Sensors

1 Answer

Replaced batteries, outsid temp. does not display


Base Station Battery Installation
·Remove the printed vinyl label from the LCD screen of the base station
·Position the remote sensor near the base station
·Open the battery compartment at the back of the base station and insert (2) AA batteries according to the polarity markings. Replace the battery compartment cover.
·Within a short time the RF signal icon (located to the left of the outdoor temperature channel indicator) will start flashing. This indicates that the base station is ready to pick up the RF outdoor temperature signal from the remote sensor. It will continue to flash for 3 minutes or until the signal from the remote sensor is detected.

Register the Remote Sensor
·Open the battery compartment at the back of the remote sensor and slide the channel selector switch to your desired channel. For the first remote you may select any channel, for additional remotes select any unused channel
·Insert (2) AAA batteries according to the polarity markings. Be sure to install the batteries in the remote within the time that the RF signal icon is flashing on the base station.
1541 WeatherGuide Wireless Weather Forecaster with Barometer

Jan 05, 2016 | Taylor Measuring Tools & Sensors

1 Answer

Modelws 7013u how to replace and reset batteries


In systems with an outdoor transmitter and an indoor receiver, the usual battery replacement procedure is to start with the outdoor transmitter first, allow time for it to start sending data, then install the replacement batteries in the indoor unit. You should see the outdoor temperature being displayed.

Jan 03, 2015 | Measuring Tools & Sensors

1 Answer

Cannot get the weather station model ws-916ou-it to show outside temperature


I have three of these WS-916OU-IT units. After a few years, the outside sensor just fails. You will get dashes and a "TR" low battery signal, even if the batteries are good
just buy another whole weather station (short money) and set both the old and new weather station unit to receive from the single new outdoor sensor.
To do this - just follow the procedure for a single sensor - that is - put the batteries in the new sensor - then within 30 seconds - put the batteries in all the weather stations - they will all pick up the same outdoor sensor.
I now have three units running off of one outdoor sensor.
Seems a bit silly, but it works.

Feb 27, 2012 | Measuring Tools & Sensors

3 Answers

The weather Forecast Icons don't change on my honeywell weather station model # TE852W


Hi,

This problem could arise due to various reasons
1)Replace the batteries in remote sensors
When the batteries are properly installed, the remote weather sensor will resume sending signals to the main unit.To enforce an immediate remote signals search, press and hold
DOWN on the main unit.

2)Remote thermo-hygrometer sensor could be weak in sending the signal about weather Forecast.Test it properly.

3)Reset the unit and check


post a comment for further assistance.
Thank you for using fixya have a nice day:-)

Sep 11, 2010 | Honeywell TE852W Weather Forecaster With...

Not finding what you are looking for?
Measuring Tools & Sensors Logo

Related Topics:

1,905 people viewed this question

Ask a Question

Usually answered in minutes!

Top Measuring Tools & Sensors Experts

Vuk B

Level 3 Expert

683 Answers

Brad Brown

Level 3 Expert

17162 Answers

Tom Chichester

Level 3 Expert

44045 Answers

Are you a Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...