Question about Pool & Spa

1 Answer

How to repair a snowblower impeller that is stuck. No debris in sight.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Master
  • 8,204 Answers

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why will the impeller handle not stay locked down on my snowblower

this is the proper method of operation as you describe now , if it stuck down before then that was a miss operation and should have been repaired as that was an unsafe method of operation and not what the CSA and mfg intended im sure

your hands should never be able to leave the drive or augar control and it continue to run along as if you had the handles , this would make it far to easy for you to get your hands/feet into a moving part accdentaly and hurt you

Mar 05, 2015 | Garden

1 Answer

Rock stuck behind impeller on swisher snowblower model 627851xo7a how do I remove auger and impeller

if rock is quartz or grannite use a torch to heat them up and dose it with cool water , shatters the rock into sand happend all the time in the quarry i worked at on heavy equipment , that torch idea worked everytime

Dec 09, 2014 | Swisher Garden

1 Answer

I am looking for a manual for a craftsman snowblower model c459-52101

go to sear web sight om line they will have one if its not five years old

Sep 03, 2014 | Craftsman Garden Tractor Snowblower...

1 Answer

Swisher 27" snowblower front impellers turn free

Hi Craig,

Most snowblowers incorporate "shear pins" between the motor and auger. A shear pin looks similar to a nut and bolt or pin that couples the drive to the auger - but it designed to break or shear off to prevent damage to the auger or motor in the event of a jam or overload. They look like these:



Only the shear pin recommended for your particular brand and model snowblower should be used. Under no circumstances should a regular bolt or other steel pin be used instead of a shear pin. Check your manual or consult with Swisher to determine the correct shear pin for your snow blower.

I hope this helps & good luck!

Dec 21, 2012 | Garden

1 Answer

Low pressure in filter after pump 5-10psi

This would indicate a problem on the suction side of the system. Make sure all the baskets are empty and clean. Debris stuck in the impeller will also cause this problem. You may be able to reach the impeller and clear the debris without taking the pump apart. Just make sure the pump is not going to start running while you have your fingers near the impeller.

Sep 03, 2011 | Pentair "Pentair" In Ground Pool Pump ...

1 Answer

Hi, Wayne PC4 pump doesn't work. Can anyone help me?

The most common issue with these pumps is that the impeller gets stuck from non usage or from debris getting stuck in the impeller.
Take the cover off of the pump section and make sure that the impeller is free of debris and that it will turn freely. If it turns hard you may be able to free it by working it back and forth. This may take some time to do. I'm not sure about this particular pump, but on some you can get a lubricant like WD-40 worked into the pump and motor bearing also...
If the impeller is spinning frreely and the motor still does not turn on then you have a bad motor. To replace this motor will probably cost nearly the price of a new pump. It may be better to just replace the whole pump.


Mar 15, 2010 | Wayne Water Systems Plumbing

1 Answer

Ariens snowblower impeller not throwing snow

Sounds like you have a broken or partially broken shear pin in the auger.Check along the auger[machine off]and see if there is what looks like a bolt anywhere along the auger shaft.If there is [and there will be] remove and inspect it and you will see why the auger is not working.Next time,never clean out a chute or auger while the engine is running,people loose limbs this way.

Feb 13, 2010 | Ariens 34 In. Zoom Series Riding Mower

1 Answer

How can I keep my 2 stage snowblower in high?

I will assume you are referring to the 2 stages in the front of the machine. The spiral auger rakes are the first stage, they are designed to collect the snow and feed it to the impeller. The impeller is the 2nd stage and is to throw the snow up the chute. The lower rakes in the front do nopt throw snow only collect it.

Jan 09, 2010 | Mtd Garden

Not finding what you are looking for?
Pool & Spa Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pool & Spa Experts

Jay Finke
Jay Finke

Level 3 Expert

1368 Answers

Bill Jordan

Level 2 Expert

372 Answers

David Spradling
David Spradling

Level 3 Expert

6889 Answers

Are you a Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides