Question about Panasonic Office Equipment & Supplies

1 Answer

Panasonic Workio 1810 - Tray 1 Add Paper Message

Hi We have a Panasonic Workio 1810, after reloading the empty A4 paper tray it makes a noise after switching it on then 'Tray 1 add paper' comes up on the display even though the tray is full of paper.
Any ideas?
Thanks!

Posted by on

  • Anonymous Mar 26, 2014

    add paper problem whilst filled

  • Anonymous Mar 26, 2014

    add paper indication problem whilst filled

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Panasonic Master
  • 6,696 Answers

First why is the tray set for size A4 Paper. That is metric size paper for oversea locations. Should be set for 81/2"x11, or 11"x81/2.. is there any paper stuck behind the 1st tray? are the guides that hold the paper in place in the draw snug up aganist the paper in the draw. is the bottom sheet of paper in the stack/rem of paper benton the edge. All sheets of paper in the draw must be flat.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Posted on Jul 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have problem on my printer workio 1820 e,it always say add paper tray no.1 which already has paper...i dont know whats the problem


your interlock switch of the front door is not working. u have to remove the front cover and then short or replace the interlock switch.

Jul 02, 2011 | Panasonic Workio DP-1820E Copier

1 Answer

In printer it showing Tray 1 ADD PAPER but [paper is added to the tray still it is showing that error so what to do ? give me the solution.


1.May be because of paper sensor.try to change it

2.may be you have given wrong paper size.u might have give wrong paper size.for ex for A4 paper u might have given some other size like a3. check this it will work for u

Jan 31, 2011 | Panasonic WORKiO DP-1520P All-In-One Laser...

1 Answer

How do I have printer switch from empty paper tray 1 to the full 550 paper tray 2


Make sure the paper type and size in both trays are the same. If you are using letter size for both trays, make sure the settings in tray 1 and 2 are the same. If the settings are the same and it still fails to grab from the full tray change the engine settings in diag mode. Hope this helps but if you need more assistance, leave a comment and I'll get back to it. Thanks.

May 10, 2010 | Lexmark X464DE Mono Laser MFP, 38ppm A4...

1 Answer

My pansonic 1820p digital copier dislays error code E02-01. The main motor & Tray 1 lifting motor do not run, from kingsley I. O.


The following might work:

Switch off at mains, remove paper from tray 1, close tray 1, switch on, replace paper when prompted.

Hope this helps.

Jan 13, 2010 | Panasonic Workio DP-1820P Laser Printer

1 Answer

Whenever i switched on the panasonic dp-1520p it displays tray no.1 add paper ,even the paper added. and did not prints .


Ad paper mean paper not response your printer.it is problem paper sensor,it may be displace,check and clean it.

Dec 09, 2009 | Panasonic WORKiO DP-1520P All-In-One Laser...

1 Answer

Message keeps saying out of paper and paper tray is full.


ok heres what u can do go to ur printer options and check if the paper is set to "letter" or "a4"

Mar 09, 2009 | Brother MFC-8460N All-In-One Printer

1 Answer

How to set the paper size in the trays?


most are set by the trays itself, when you adjust the "guides" that go against the paper it adjust some levers on the side or back of the tray which push on some sensors behind the tray.
Some however you need to turn a dial in the tray to the paper size you need.
make sure the guides are snug against the paper, the dial or settings are correct and that there is no paper behind the tray.
Also I'm not sure what country you are from but in the US we do not use A4

Nov 23, 2008 | Panasonic Workio DP-2500E Copier

4 Answers

DP-1820E - Contact Your Dealer - Printer Error E02-01


E02-01 refers to the tray 1 lift motor either you have a bad motor or there's a problem with your main board. good luck

Apr 23, 2008 | Panasonic Workio DP-1820E Copier

1 Answer

Paper jam and possible failure to pull A4 paper ?


1- you must remove the jam paper first
2- set the tray to LETTER or LEGAL not A4
A4 is european size not used in the U.S

Make sure the paper adjuster in the tray is touching the end of the paper size, also there should be some markings in the tray.

The noise is coming from the jammed paper, it is trying to feed itself but is stuck.

Dec 24, 2007 | Office Equipment & Supplies

3 Answers

Crooked Copies


dear sir please check the upper heat roller claws set,may be one of them is bended up

Sep 27, 2007 | Panasonic Workio DP-4530 Copier

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

726 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6696 Answers

Mitch S
Mitch S

Level 1 Expert

25 Answers

HEMANT GROVER

Level 2 Expert

167 Answers

Are you a Panasonic Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...