Question about Heating & Cooling

Open Question

How do I reset my thermostat going on 7.30 off at 10 am back on 12 till 1pm back on at 5pm till 10pm please

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: i have a intermatic digital 3 circuit timer and

1) You have P1353 timer.
This is a complicated timer for beginner because timer can be set up many different ways for multiple operations.

Open following link for manual: The manual is a large file and may be impossible to download on dial-up.
http://waterheatertimer.org/Intermatic-trippers-and-parts.html#P1353
http://waterheatertimer.org/pdf/Intermatic-P1353-manual.pdf
Smaller manual is available but some pages are turned sideways which is not so handy.
http://waterheatertimer.org/pdf/P1353ME-instructions.pdf


P1353 instructions start page 28 of larger manual.
Manual is longer than space allowed for free answer, so we can work in stages.
At any time, you add a comment and I will respond -and/or send a photo of your wiring, etc
http://www.fixya.com/support/r6568559-post_photograph_fixya_questions_answers

1) You want Mode 2 so low and high speeds are not turned ON at same time.
2) Wiring requirement: High speed is connected to terminal 3, low speed connected to terminal 2 as shown in fig 4-4 > this is where you can send a photo or add a comment and clarify how your timer is wired.

3) Page 30 goes through steps for setting the mode. Remember you want Mode 2.
4) Page 31 shows how to set current time of day.

5) Page 31-2 shows steps for programming each circuit.
Assuming that your wiring matches fig 4-4 mentioned above:
High speed is circuit 1
Low speed is circuit 2

Once you digest this information, it will narrow down the questions and I can answer those one at a time with more detail if needed.
Or you can re-post a question and I will probably catch it.

Also take advantage of fixya expert assistance live.
For a price, expert works with you while you work on timer or any do-it-yourself project.
Fixya is always less expensive than a service call.

Posted on Apr 04, 2011

SOURCE: Intermatic Digital 3-Circuit Timer Mechanism

Same answer applies as one sent earlier.
Take some time and read answer, or re-post question and pay for interactive answer with fixya expert who can walk you through the steps for a price.

1) You have P1353 timer.
This is a complicated timer for beginner because timer can be set up many different ways for multiple operations.

Open following link for manual: The manual is a large file and may be impossible to download on dial-up.
http://waterheatertimer.org/Intermatic-trippers-and-parts.html#P1353
http://waterheatertimer.org/pdf/Intermatic-P1353-manual.pdf
Smaller manual is available but some pages are turned sideways which is not so handy.
http://waterheatertimer.org/pdf/P1353ME-instructions.pdf

P1353 instructions start page 28 of larger manual.
Manual is longer than space allowed for free answer, so we can work in stages.
At any time, you add a comment and I will respond -and/or send a photo of your wiring, etc
http://www.fixya.com/support/r6568559-post_photograph_fixya_questions_answers

1) You want Mode 2 so low and high speeds are not turned ON at same time.
2) Wiring requirement: High speed is connected to terminal 3, low speed connected to terminal 2 as shown in fig 4-4 > this is where you can send a photo or add a comment and clarify how your timer is wired.

3) Page 30 goes through steps for setting the mode. Remember you want Mode 2.
4) Page 31 shows how to set current time of day.

5) Page 31-2 shows steps for programming each circuit.
Assuming that your wiring matches fig 4-4 mentioned above:
High speed is circuit 1
Low speed is circuit 2

Once you digest this information, it will narrow down the questions and I can answer those one at a time with more detail if needed.
Or you can re-post a question and I will probably catch it.

Also take advantage of fixya expert assistance live.
For a price, expert works with you while you work on timer or any do-it-yourself project.
Fixya is always less expensive than a service call.

Posted on Apr 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much is a picture tube for ilo tv


tvpartsguy com
PHONE: (909)-598-9777 ADDRESS: 260 Paseo Tesoro
Walnut CA 91789
HOURS: M-F: 8am-5pm
Sat: 8am-1pm
Sun: Closed

Jun 07, 2015 | iLO Televison & Video

1 Answer

Remove front grill


both are covered in the fsm.
https://www.techauthority.com/en-US/Pages/Home.aspx'

the latter is by engine sizes, not stated.
water sending, ? the ECT? eng. coolant temp.?
no symptoms posted, but im to assume the scan tool shows
low ECT readings and the dash cluster engine temp are both low?>
if both are low, then the engine thermostat is bad. 99 out of 100.
next time post symptoms we can be on same page.
i guess you know where the ECT is? and wanted to know out to
remove it?
sigh
2.4 liter , face engine at 5pm on right cam, is ECT
or 1pm on top idle pulley. has a wire there.
3.7L
see photo below.

#3 unscrew it, after draining coolant.

25252690-cx5p5jsxher3ki1yzdn3ijnx-2-0.jpg

Oct 22, 2014 | 2004 Jeep Liberty

1 Answer

How do I figure military time


add 12 to the time starting at 1pm. ie; 1pm = 13:00. Before 1pm you can refer to the time in usual manner such as 7am or 7:00. hope this helps. Also you can have military time (24 hour format) mixed with 60 minute format (13:45 = 1:45pm) or decimal (13.50, 13.5 = 1:30pm) as well.

Sep 28, 2014 | Lathem Manual Clock Time Recorder - 2126

2 Answers

Error message ERR


Product Phone Number Hours Support Website SURFboard® Cable Modems and Gateways 1-877-466-8646 Sun-Sat 7AM-11PM CST Website link Touchstone Cable Modems, Gateways and EMTAs 1-877-682-7747 Sun-Sat 7AM-11PM CST Website link DSL Modems and Gateways 1-877-466-8646 Sun-Sat 7AM-11PM CST Website link Video 1-877-466-8646 Sun-Sat 7AM-11PM CST Website link Software 1-877-466-8646 Mon-Fri 8AM-8PM CST Website link

For other Motorola products, please visit the product's website for your support questions.
Product Phone Number Hours For general product questions and technical support
on your Android-powered Smartphones and Devices
e.g. Motorola XOOM™, DROID RAZR™, DROID Pro,
Motorola ATRIX™ 4G, MOTOACTV™ 1-800-734-5870 Mon-Fri 7AM-10PM;
Sat-Sun 9AM-6PM CST Motorola Fitness Devices
e.g. MOTOACTV 1-800-734-5870 Mon-Fri 7AM-10PM;
Sat-Sun 9AM-6PM CST Non-Android Mobile Phones & Accessories
e.g. Motorola Karma™ QA1, MOTORAZR2™ V9,
MOTO™ W233 renew 1-800-331-6456 Mon-Fri 7AM-10PM;
Sat-Sun 9AM-6PM CST iDEN i-series/ic Series
e.g. i776, i425
(Nextel, Boost Mobile, and Southern Linc) 1-800-453-0920 Mon-Fri 7AM-10PM;
Sat-Sun 9AM-6PM CST TTY Support 1-888-390-6456 Mon-Fri 8AM-5PM CST
reference: http://arris.force.com/consumers/pkb_Home_ConsumerCallUsPage
Call Us

Mar 20, 2014 | Motorola Televison & Video

1 Answer

Do you know if they sell a replacement for the front louvered grill in the lazer 73? Mine is damaged and I removed it from the frame and need a new one.


Parts are available. Contact Valley Power Equipment, Customer Service Dept 1-877-360-3507
Monday - Friday 8am - 5pm ET, Saturday 8am - 1pm ET .

Hope this helped you.

Jul 01, 2011 | Rinnai Toyostove Direct Vent Heater:...

2 Answers

I HAVE A HONEYWELL T8600D 2028, CHRONOTHERM IV PLUS DELUXE PROGRAMMABLE THERMOSTAT, AND THE TIME/DATE SETTINGS DO NOT HOLD; EVERY MORING, IT FLASHES MONDAY, 1pm. ANY SUGGESTIONS? I RESET TIME/DAY,...


pknab, I have the same problem. And it comes down a few things: 1) the flashing 1:00 indicates that you've lost power, and the system needs to be reset. 2) Reset means taking out the batteries for longer than 5 minutes. 3) You have to change your filter monthly. There's one in the cold air return and another one in the furnace. If you don't, your FURNACE may be causing number one (my conjecture). 4) We had an electrical storm 2 days ago--nothing else in the house lost its sense of time...but...well...the online operating manual is difficult to find try http://customer.honeywell.com/techlit/pdf/69-0000s/69-1400.pdf or http://dl.owneriq.net/e/e67c2c91-73c2-4bd8-abc8-91d843a27658.pdf (but it doesn't tell us this stuff...I'm still looking for the meaning of the EEE in the display..perhaps I have repowered the thermostat/furnace in the wrong order).

Dec 07, 2010 | Honeywell Programmable Thermostat Heater

1 Answer

I am having trouble with yahoo finance page, it is not loading properly. I am not that computer literate and I do have an old computer but this is the only proplem I have. It was fine till last week than...


I doubt the problem is with your computer. Most likely yahoo was having problems. Try again at a time when yahoo traffic is light and see what happens. I've used Yahoo finance daily for a couple of years and have had occasional problems around peak periods (noon to 1pm, and from the exchange closeing bell until about 5pm

Jan 25, 2010 | Microsoft Windows XP Professional With...

1 Answer

Loss of signal


It is most lkely the battery, chane the battery and recharge it. batteries collapse after about 2 -3 years depending on use and abuse. If you have it plugged in when starting the engine the battery will deteriorate quicker and eventuslly fail. resting the battery can cause some charge to return, often sufficient to run it for short periods before it once again fails due to output being greater than the chrging rate.

Jun 30, 2009 | Tomtom ONE GPS Receiver

1 Answer

Power cord


call 1-800-948-1358 ask for Buck mon.-fri. 9am-5pm est sat.9am-1pm est

Apr 10, 2009 | Vacuums

1 Answer

CTX Panoview 630 Monitor


Panoview 630 Power Connector pinouts:
It has been many years since the question was posted but who knows, maybe this will help someone. Looking at the end of the connector clockwise from 1-oclock position:
1pm:NC
3pm:+12
5pm: no pin
7pm:+5V
9pm:+5V
11pm:GND
shield is GND
+5V@3A
+12V@1.5A
(you can modify an Apple ADB cable to work)

Mar 15, 2007 | CTX Panoview 630 Monitor

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Heating & Cooling Experts

paulcarew

Level 3 Expert

2461 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Donni Steen

Level 3 Expert

659 Answers

Are you a Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...