Question about Insignia Televison & Video

1 Answer

How can I fix this issue with my television?

I have an Insignia NS-LCD26A TV whose power instantly went out. I waited a while to remove the back cover and once I did, I discovered several capacitors had leaked plus some were tipped over. This was all on the power supply board. Some of the (now) dried chemical got on the wire head leading to I think either the LED driver board or the T-Con board. I was unable to remove the main board/motherboard's cover but the capacitors on the outside of the cover looked to be in good condition. The part # for the power supply board is: 6HU0122014. The main board's part # is: 6HA0226911. Is it worth trying to replace potentially two parts? I know for sure the power supply board is in need of a replacement but I am not confident about the main board even though no leakage spread onto it. Note: I received this TV as a gift so I put no money into it.

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Insignia Master
  • 74,251 Answers

Sounds like The main power supply regulator section circuit fault. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/ It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size.
Search the site by type in the "brand name" to your device; in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

Posted on Dec 10, 2016

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: How to remove the back from Insignia NS-32LCD?

I unscrewed all the screws in the back, detached the tv from the base, and was able to get the back off. I ordered a new power supply board and will install it to see if it fixes the problem with the tv (won't turn on, insignia light alternates between red and blue). I didn't notice any problems with "swollen" capacitors, so if the new power board fixes the problem I'll update this website.

Posted on Jan 28, 2009

skotkolr
  • 558 Answers

SOURCE: Insignia TV model NS-LCD26A power up problems

you are correct power pack has bad capacitors, doing what you did may have damaged other components in the power pack, or main video board. let me know what you want to do.

Posted on Apr 05, 2009

  • 8457 Answers

SOURCE: Replaced main board in Insignia NS-LCD19 TV and

Check all connections first,try agian.After that Change the LCD Inverter board might also dead.The inverter help backlight to screen to come on.

Posted on Jan 13, 2010

futurework
  • 70 Answers

SOURCE: insignia ns-pdp50 plasma. pop of death, audio but no video

I suspect that your supply has gone bad. You will need to find the service manual for voltage measurements. If you want to get replacement boards many can be found on ebay or you can check www.shopjimmy.com they stock boards for many units and I have had no problems.

Posted on May 04, 2010

budmrtn
  • 11361 Answers

SOURCE: INSIGNIA 26" LCD TV > > MODEL# NS-LCD26F

If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on:

Please see my basic troubleshooting guide here:
http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide

http://s807.photobucket.com/home/budm/allalbums

http://en.wikipedia.org/wiki/Capacitor_plague

Posted on Aug 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a insignia.MODEL NS-LCD26A. SERIAL #2881LC26HA37H05804. WHEN I TURN IT ON THE SCREEN IS JUST WHITE. WHAT IS WRONG?AND WHAT SHOULD I DO?


It sounds that the main digital board to this set is not functioning. There are many reasons for this, and is not a user repairable fault. Contact any service technician.

Oct 24, 2013 | Televison & Video

1 Answer

Need base for Insignia NS-LCD26A


Parts for Insignia TVs can be ordered by visiting BestBuy.partsearch.com or calling 1-888-237-8289.

Apr 07, 2010 | Insignia LCDTV26 26 in. Television

2 Answers

I need to know Insignia remote code


You can find many universal remote control codes at InsigniaProducts.com, just search for your TV model number and click on the Support Tab.

Feb 09, 2010 | Insignia LCDTV26 26 in. Television

1 Answer

Remote COntro COde for Insignia NS-LCD26A


You can find remote control codes for your TV here. Select your exact model number. If the codes listed don't work, there is a listing of compatible brand codes that you can try.

Sep 30, 2009 | Insignia LCDTV26 26 in. Television

1 Answer

The audio went out on my insignia NS-LCD26A. It


It's likely that the TV will require service. You may take the TV to the retailer of purchase to arrange for repairs.

Sep 23, 2009 | Insignia LCDTV26 26 in. Television

1 Answer

Insignia (ns-lcd26a) picture problems


ns-lcd26a
Hi,I fixed my here's issues i had and the fix i did..
ns-lcd26a
Every now and then i would get snow and a pink picture.
Then tv stop turning on .

To fix i seen on main board capacitor cp25 and cp28 near the heat sink was bad
They were both 470uf 35v...
on the power board i seen c531 47uf 50v was bad.
i also heated up the heat sink on the main board to resit the chip ,,
and tv now works

I didnt bother putting the huge shield back on main board i figure it was a issue to over heating the cpu instead take the hit to the brain from the fcc radio wave lol

First do the 3 caps and see if it works if not then do the blow dryer to the heat sink on main board

Aug 20, 2009 | Televison & Video

2 Answers

Insignia NS-LCD26A 'No Signal'


someone kicked the antenna out of the plug? or the antenna fell off the roof Sometimes its not even your place that has the problem Try another channel to see if its just the TV station

Jun 04, 2009 | Insignia I-LC23Q1 23 in. HD-Ready LCD...

1 Answer

Insignia LCD TV 26" Colored Streaks/No Picture


You have a bad LCD panel. The cost of a repair would exceed the value of the unit. Panel will probably cost, if you could find one, around $300-$800.

Jan 02, 2009 | Insignia LCDTV26 26 in. Television

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Insignia Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74251 Answers

Jaime Hernandez

Level 3 Expert

2318 Answers

Cindy Wells

Level 3 Expert

5127 Answers

Are you an Insignia Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...