Question about Heating & Cooling

Open Question

I have a country flame nps 1000,it won t feed fast enough to stay lit by is ok w hen u push manual button

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 12104 Answers

SOURCE: country flame nps-1000 made in 1996 has a lazy

not getting enough air -clean and vacuum unit and check fresh air flow damper is not opened enough need more air or flue clogged and needs cleaning

Posted on Feb 15, 2010

georgegouvas
  • 57 Answers

SOURCE: need a blower for a country flame nps-1000

go to computer,punch up name mod. number,hit search....

Posted on Nov 28, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I've got good flame replaced Powerpile pilot won&#t stay lit


The flame sensor is not producing enough volts to hold the gas valve open for the pilot light. Make sure the SIDE of the pilot flame is touching the sensor. If it in engulfed by the flame it won't work right.

Jan 01, 2016 | Cozy Heating & Cooling

1 Answer

Sime boiler pilot light


Sounds like an old boiler. It is not on timer and has to be lit manually. Push in the gas button and hold and push the sprung ingnition button to greate spark. Continue to hold in gas button 1-2 mins and release. The pilot light should then stay on. The flame will have heated the sensor in the combustion chamber and the boiler thinks that there is a flame and will allow the main gas jets to light when demanded . If the flame does not stay on clean the sensor prongs with emery cloth but do wait until they are cooled. You have open up the combustion chamber for access
The 1-2 mins above varies

Apr 07, 2014 | Water Heaters

1 Answer

Have an rlp30 reddy heater, have spark and gas but will not light.


wile red button is pushed no flame or turns off when the button is released the flame dies ? if no flame tank is too small or spark isn't in far enough to catch gas . if flame is present with button down then the over heat switch on the in line thermal coupler could b bad u can check the over heat switch with a jumper between the two wires and if it stays lit you got it if it goes out then its the thermal coupler that's bad

Dec 12, 2013 | Reddy HEATER RLP30 30,000-BTU PORTABLE LP...

1 Answer

Pilot won't stay lit...gaffers&sattler model B35


Hit the flame sensor next to the pilot with sandpaper. If it still doesn't work replace it.

Feb 26, 2013 | Heating & Cooling

1 Answer

We have a Dometic 3way fridge, the gas stayes lit only as long as I hold the button.


It appears that you have a bad thermocouple. This senses the heat and should allow the gas valve to stay open after the flame has been lit for approximately 30 seconds. By pushing the button you are manually opening the valve. Check to make sure the thermocouple is resting in the flame and is getting the proper heat.

Jan 21, 2013 | Dometic Refrigerators

1 Answer

Need a blower for a country flame nps-1000


go to computer,punch up name mod. number,hit search....

Nov 28, 2012 | Heating & Cooling

1 Answer

My furnace lights but only stays lit couple sec can hear a click then goes out


Sounds like it is not proving flame, to check you need a meter that will read DC microamps. without knowing the brand I can't say what you should be looking for. Trane furnaces need at least 1 DC microamp to prove presence of flame. Usually you will see 2 - 2.6 or so, but it depends on what the manufacturer specs to prove flame. At minimum you can pull the burners out and clean them really good (especially the cross-over wings) because if the flame doesn't roll down to the sensor fast enough during the trial for ignition it will recycle and eventually lockout. If it stays lit longer than 20 sec, it most likely is proving flame and cycling off on high limit because the blower is not coming on. The typical blower on delay is 45 sec from the time flame is proved to when the blower is energized

Nov 02, 2010 | Coleman Heating & Cooling

1 Answer

Country flame nps-1000 made in 1996 has a lazy flame, low heat output, and having a difficult time regulating auger feed any suggestions


not getting enough air -clean and vacuum unit and check fresh air flow damper is not opened enough need more air or flue clogged and needs cleaning

Feb 15, 2010 | Napoleon Auburn Pellet Stove Heater

1 Answer

Pilot will not stay lit and heater will not light


thermocouple probablly bad, is the flame covering the thermocouple.
the flame has to hit top portion of thermocouple to work correctlly.

Feb 14, 2010 | Endless Summer (GA200209) Stainless Steel...

2 Answers

I have a set of new gas (LP)fire logs just installed pilot will not stay lit manual says check flame to thermal couple but there is not a thermal couple visable. nor is it listed in parts manual. It is a...


The thermocoupleis about 3/16" in diameter and slides up through a hole right beside the pilot flame. Sometimes it doesn'tget pushed up far enough to come out the top into the flame. check the bottom of the pilot assemblynext to the silver pilot tubing, there the thermocouple is attached to a very small copper tube( 1/16") and this tube runs back to the gas valve. If it is there see if you can push iy up into the hole next to the silver tubing. unless the thermocouple can feel the flame the pilot will not stay lit, Hope this helps.

Oct 01, 2009 | Heating & Cooling

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Heating & Cooling Experts

paulcarew

Level 3 Expert

2463 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Donni Steen

Level 3 Expert

659 Answers

Are you a Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...