Question about Exercise & Fitness

Open Question

Gold's gym trainer 480 & incline is not working. Took motor cover off & noticed that the 1 plug was loose. Can't get it to go back in & over the 3 metal prongs w/o bending or moving.

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ercupa190
  • 12223 Answers

SOURCE: I need a owners manual for a Golds Gym 480 trainer

Dear Sir:

I will try to help you, please go for free to next page:

http://fitness.manualsonline.com

If you need further assistance, please reach me.

sincerely. God bless you.

E.CUADRA
MANAGUA, NICARAGUA. C.A.

Posted on Oct 17, 2011

Ad
ercupa190
  • 12223 Answers

SOURCE: golds gym trainer 480 treadmill stays at full

Dear Sir:

 

I will try to help you, you must use some basic tools: screwdriver, Hex, Dvom(DigitalVoltemeter):

 

http://www.youtube.com/watch?v=MIIxoPtvhy8

http://www.youtube.com/watch?v=M7qJrRbdfBc

http://www.youtube.com/watch?v=Uzf4az4RRDE

http://www.youtube.com/watch?v=9G4MZh8JO2Q

 

This will be fix it.

 

In another machines: You will follow the next:

 

Any board control for elevation motor has 2 LED : DN= Down  +UP= UP for Elevation Motor, when you push the button for Down the LED Yellow or Green  DN, will be going Down Lit, and Viceversa.

 

 The Relais in this case 2 relais, will be operated by 12 VDC, you must Clean The Contact, with Special Solvent . You can buy from Radio Schack. Check the Fuse with Dvom, and Finally after you must check this, and the motor is Not O.k is Faulty. Replace.

 

But check before any Wire loose, before to concluded that the Motor is Bad.

 

If you need further assistance, you can reach me, sincerely God bless you.

 

E.CUADRA

MANAGUA, NICARAGUA. C.A.

Posted on Oct 19, 2011

ercupa190
  • 12223 Answers

SOURCE: Golds Gym Trainer 410 belt and incline do not work

LUBE THE DECK BELT SEE THE VIDEO ATTACHED
2) RUN THE SOFTWARE CALIBRATION FOR EASY DIAGNOSE, TROUBLESHOOTING AND FIX IT. GO under the HOOD motor, and follow the steps.
God Bless you
12_13_2012_8_42_51_pm.jpg

Posted on Dec 13, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Golds Gym trainer 480 treadmill minimum speed is 3 miles at lowest setting and it will not slow down when pressing the down arrow


Gold's Gym Treadmill Product Support ' ManualsOnline.com

fitness.manualsonline.com/support/golds-gym/treadmill/
My goldsgym treadmill just goes up and down when t. Gold's Gym ... my treadmill walking belt will not turn. ... Golds gym trainer 480 start button stopped working.

Repair Your Own Treadmill With Mark Peterson - YouTube

? 1:16
https://www.youtube.com/watch?v=B997gX07hW4
May 6, 2008 - Uploaded by Mark Peterson
A certified Fitness Specialist by the cooper clinic in Dallas, and a personal trainer for the first 16 years of my fitness career. .... I purchased a used Golds Gym Treadmill model# GGTL396100 which I tested when buying ... The treadmill will fully incline thennot go down, I have tried to recalibrate the incline ..

Nov 26, 2015 | Exercise & Fitness

1 Answer

The buttons on my tredmill only work when they want too why.. its a trainer 480 from gold gym


Chances are the oil and sweat from your fingers have gotten under the buttons, the oil film insulates the contacts and they stop working. or work intermittently. Open it up, clean all the contacts on the circuit board (q-tip & rubbing alcohol), as swell as the bottom of each button, then reassemble.

Feb 18, 2015 | Exercise & Fitness

1 Answer

I have a Gold's Gym Trainer 480. model ggtl39608. Everything was working fine. Now the incline will not work & the control panel will not light up.


This problem needs more details to service....seem like you have multiple problems...better to call for service 877-805-1030

Jan 01, 2014 | Golds Gym Exercise & Fitness

1 Answer

I have a gold gym trainer 410 treadmill that by a power out stop working I notice the motor card was burned out so I bought a used one in ebay but still wont turned on what could be wrong with it


you may have a faulty board.Does it have a light on it when you turn it on. If not it is faulty or the power lead is faulty or safety switch is faulty.
If all else fails call a tech to come out and look at it for you.

Sep 25, 2013 | Golds Gym Trainer 410 Treadmill

1 Answer

I have a Gold's Gym trainer 410 treadmill. I


please RUN the software calibration for easy diagnostic and fix it.
Go under the HOOD cover for motor, and see the instruction and follow the instruction
God bless you

Jul 20, 2013 | Exercise & Fitness

1 Answer

Golds Gym Trainer 410 belt and incline do not work


LUBE THE DECK BELT SEE THE VIDEO ATTACHED
2) RUN THE SOFTWARE CALIBRATION FOR EASY DIAGNOSE, TROUBLESHOOTING AND FIX IT. GO under the HOOD motor, and follow the steps.
God Bless you
12_13_2012_8_42_51_pm.jpg

Dec 13, 2012 | Golds Gym Trainer 410 Treadmill

1 Answer

My Golds Gym trainer 480 treadmill wont start and none of the buttons work except for the up and down arrows for the incline.


my gold,s gym trainer 480 will ot run,everthing light up on console. could it be a fuse?

Oct 20, 2012 | Exercise & Fitness

1 Answer

Golds gym trainer 480 treadmill stays at full incline and wont decline


Dear Sir:

 

I will try to help you, you must use some basic tools: screwdriver, Hex, Dvom(DigitalVoltemeter):

 

http://www.youtube.com/watch?v=MIIxoPtvhy8

http://www.youtube.com/watch?v=M7qJrRbdfBc

http://www.youtube.com/watch?v=Uzf4az4RRDE

http://www.youtube.com/watch?v=9G4MZh8JO2Q

 

This will be fix it.

 

In another machines: You will follow the next:

 

Any board control for elevation motor has 2 LED : DN= Down  +UP= UP for Elevation Motor, when you push the button for Down the LED Yellow or Green  DN, will be going Down Lit, and Viceversa.

 

 The Relais in this case 2 relais, will be operated by 12 VDC, you must Clean The Contact, with Special Solvent . You can buy from Radio Schack. Check the Fuse with Dvom, and Finally after you must check this, and the motor is Not O.k is Faulty. Replace.

 

But check before any Wire loose, before to concluded that the Motor is Bad.

 

If you need further assistance, you can reach me, sincerely God bless you.

 

E.CUADRA

MANAGUA, NICARAGUA. C.A.





Oct 18, 2011 | Exercise & Fitness

Not finding what you are looking for?
Exercise & Fitness Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Exercise & Fitness Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Howard
Howard

Level 2 Expert

115 Answers

Tom Chichester

Level 3 Expert

35487 Answers

Are you an Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...