Question about Measuring Tools & Sensors

1 Answer

I have a model #WS-9037un-it with a model TX29Uremote transmitter. When I removed batteries there was a reading on it when I put in new batteries no temp. waited several hours.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Master
  • 34,089 Answers

  • Remove all batteries
  • Install known-good batteries in the transmitter. Wait for transmitter to initialize and begin sending temperature data
  • At the receiver, install known-good batteries. You should see outdoor temperature displayed

Posted on Dec 08, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The outside transmitter for my Lacross weather station, model WS-9080U-IT is not working. I replaced the batteries. How do I get it to transmit?


First remove the batteries and wait 5 minutes and then try again. If still no success, make sure that you are close enough to the sensor, take the sensor inside to the readout and see if it picks it up. If it does then there may be interference.

Dec 21, 2016 | Measuring Tools & Sensors

1 Answer

I put new batteries in Transmitter and never got any temp reading.The unit is less than 2 years old and is not working. Is there anything I can do?


  • Remove all batteries
  • Install new batteries in transmitter
  • Wait for transmitter to initialize and begin transmitting temperature data
  • Install known-good batteries in receiver
  • Observe outdoor temperature reading
If this doesn't work, the transmitter or receiver or both may be defective. I find in very cold weather the transmitter stops sending the temperature.

Dec 08, 2016 | Measuring Tools & Sensors

1 Answer

I have eight atomic clocks,none of them have the outside temperature working,all have new batteries???


If your outside temperature is not showing on your clock, that may mean that the clock and the transmitter have lost their connection. To reconnect them you must first take the batteries out of both of the units for 15 minutes. First put the batteries back into the transmitter, and then the clock. Let them sit side by side inside your home. When both the indoor and outdoor temperatures show on your clock with the same reading, or within two degrees of each other, then you may put your transmitter back outside. Remember to keep the transmitter out of the direct sun in a dry place. Also keep it away from metal, which can affect the readings.

Oct 20, 2014 | SkyScan 86742 Digital Atomic Wall Clock

2 Answers

Can't get outside temp on my atomic clock


If you still have the instructions read up on pairing the transmitter to the clock. You'll need to do that every time you change batteries on the outside transmitter. If you don't have those instructions , go to the clock's web page to get the manual for your model of clock.

Sep 23, 2014 | Home

1 Answer

Inability to access Farenheit readings. Model WS-9133U-IT. Freq. 915 MHz. Transmitter: TX37U


Keep in mind TX37U-IT should only be installed out of direct rain or sun. It could be heat or water damaged. The WS-9133U-IT shouldn't be at fault.

Jan 01, 2012 | Computers & Internet

1 Answer

I have an acurite atomic wall / weather clock but the outside temperature is reading blank. I changed the batteries in the transmitter but still no reading. Where can I purchase a new transmitter. The...


I had one of these a while back and it had a required sequence for putting in the batteries. When the signal dies and you have to replace the transmitter batteries and the clock batteries in a certain sequence. The transmitter batteries cannot just be replaced. You also had to remove the clock batteries, then put in the transmitter batteries, then replace the clock batteries.

Dec 03, 2010 | SkyScan 86742 Digital Atomic Wall Clock

2 Answers

I put new batteries into both units, the indoor unit and outdoor unit, now it is not able to read the outdoor temperature. What needs to be done?


I'm having the same problem and can't find an answer. Seems this also happened with another model we had - planned obsolescence? It was working fine, flashing due to low battery. Now, nothing from outside. Annoying.

Oct 16, 2010 | Acu-Rite AcuRite IndoorOutdoor Wireless...

1 Answer

The temperature transmitter does not communicate with the receiver. In spite of: two new sets of Duracell AAA Bateries Both the receiver and the transmitter are on channel...


Hi

Thanks for using FixYa. Try changing the radio channel by--

To change to radio channel:
1. In any of the time displays, press and hold CHANNEL for 2 seconds.
2. Press or to switch between various channels.
3. When the appropriate channel has been selected, press MODE to confirm and return to the lock- Display mode.

Also see this manual for more detailed instructions--

Oregon Scientific temperature transmitter

Please tell me the model number of your Unit so that i can provide you with model specific information.

Please do accept the solution if the issue is resolved or else revert for further assistance.

Thanks
Rylee

Sep 01, 2009 | Office Equipment & Supplies

8 Answers

Temperature Transmitter


You need new SioScan Temperature Transmitter 433 MHz. Take a look on amazon La Crosse Technology TX6U Wireless Temperature Sensor for 433 MHz units.... Hope this was helpful. cheers
temperature-transmitter-uh3jsoynacgcqh0wcsujgpyu-3-0.jpg

Oct 16, 2007 | SkyScan 86709 Atomic Wall Clock

Not finding what you are looking for?
Measuring Tools & Sensors Logo

Related Topics:

265 people viewed this question

Ask a Question

Usually answered in minutes!

Top Measuring Tools & Sensors Experts

Vuk B

Level 3 Expert

678 Answers

Brad Brown

Level 3 Expert

15557 Answers

Tom Chichester

Level 3 Expert

34066 Answers

Are you a Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...